LaCruz®, Solutions for vineyards - 57 Pages

Add to MyAgriExpo favorites
LaCruz®, Solutions for vineyards

Catalog excerpts

Power tools Shoots removing Trimming Grape harvesting Destemming

 Open the catalog to page 1

LaCruz® was founded in 2006 by Mr Andrea Cruzzolin and since then, it has become an important reference point in the wine sector. LaCruz® founds its roots in long experience and tests in a territory were the wine culture has always been strongly eradicated. Its constant innovation and improvement of knowhow in the technological and mechanical fields and the endless research of new material have set the basis for the creation of products intended for an improved efficiency in this sector and for all those using them. LaCruz® offers a wide range of products: spare parts, accessories for...

 Open the catalog to page 2

Compatible spare parts for Grégoire grape harvesters code FRSRGREG LaCruz patented shaking rod for G1, G50, G55, G56, G115 and other models. Same length as genuine rod. A box 92 cm x 20 cm x 24 cm contains 10 pcs. code FRSRGREV LaCruz patented shaking rod for G2, G60, G70, G85, G90, G107 and other models. Same length as genuine rod. A box 116 cm x 19 cm x 24 cm contains 10 pcs. code FRORGREG code FRORGREV LaCruz patented shaking rod for G2, G60, G85, G90, G107 and other models. 15 cm longer than the genuine rod. A box 120 cm x 20 cm x 24 cm contains 10 pcs. Round shaking rod for G2, G60,...

 Open the catalog to page 4

code STSXGRE code STDXGRE Left front support for shaking rod Ø 25 mm, short model, with one hole, to adapt shaking rods Ø 25 mm to old models of grape harvesters with shaking rods with Ø smaller than 25 mm Left front support for shaking rod Ø 25 mm Left front support for shaking rod Ø 28 mm Fastening kit for shaking rods supports on leg: 2 screws M10 x 30 + washers + bolts Fixing plate with 4 holes for S model shaking rod Right front support for shaking rod Ø 25 mm, short model, with one hole, to adapt shaking rods Ø 25 mm to old models of grape harvesters with shaking rods with Ø smaller...

 Open the catalog to page 5

Compatible spare parts for Grégoire grape harvesters code SCDXGRE Left catcher tray Right catcher tray code SRSXGRE code SRDXGRE Reinforced left catcher tray Reinforced right catcher tray code PRSCGRE Reinforcement or extension for all catcher trays Fixing stainless plate for catcher tray code VTSCGRE G4-type left catcher tray G4-type right catcher tray Fastening kit for catcher trays: 2 screws and 2 bolts G85/G86-type left catcher tray SW-type left catcher tray, with three holes code SCSXGRE First catcher tray fixing plate type-G4 G85/G86-type right catcher tray SW-type right catcher tray,...

 Open the catalog to page 6

Compatible spare parts for Grégoire grape harvesters SW-type left flexible catcher tray support unit Stainless steel screw M8 x 25mm for fastening SW catcher tray supports SW-type right flexible catcher tray support unit Catcher tray for PMM Grégoire harvesters, with two holes code BKPIGRE Rubber joint swinging head Bush for rubber joint 24x48x44 mm code SKGRGRE code SKELGRE Rubber ball joint 16x65x60 mm Rubber ball joint 20x75x50 mm Rubber joint 45x27x14 mm for catcher tray of PMM Grégoire harvesters code 265265G Ref. original code: 265265 Bearing bush for harvesting head Ø 38 mm Rubber...

 Open the catalog to page 7

Compatible spare parts for Grégoire grape harvesters code TEPOGRE Ref. original code: 285012 Rear flap 320X400mm code TESXGRE code TEDXGRE Left lower front flap, 3 plies Right lower front flap, 3 plies Left lower front flap, 4 plies Right lower front flap, 4 plies Left front catcher tray flap bracket Right front catcher tray flap bracket Catcher tray flap bracket left for TESXGRE Front shield extension rubber strip for G60. 2010x200mm. Front shield extension rubber strip for G50/G55. 1590x200mm. Catcher tray flap bracket right for TEDXGRE code 345009G Ref. original code: 345009 Lower front...

 Open the catalog to page 8

Compatible spare parts for Grégoire grape harvesters 320 mm main belt for Grégoire harvesters (by the meter) 320 mm plain main belt for Grégoire harvesters (by the meter) 240 mm main belt for Grégoire harvesters (by the meter) 320 mm full main belt for Grégoire harvesters, including fastener, fastener pin and holes (by the meter) 320 mm plain main belt for Grégoire harvesters including fastener and fastener pin (by the meter) 240 mm full main belt for Grégoire harvesters, including fastener, fastener pin and holes (by the meter) 320 mm plain belt, 4 plies, by the meter 320 mm plain pierced...

 Open the catalog to page 9

Compatible spare parts for Grégoire grape harvesters code NAASGRE Upper cleaner conveyor belt with fastener for Grégoire harvesters type G60. 810x250 mm Upper cleaner conveyor belt with fastener for Grégoire harvesters type G132, G152 and other models. 910x360 mm Upper cleaner conveyor belt with fastener for Grégoire harvesters type G130. 1090x500 mm Upper cleaner conveyor belt with fastener for Grégoire harvesters type G140. 950x500 mm code 286041G Ref. original code: 286041 Upper cleaner conveyor belt with fastener for Grégoire harvesters type G7. 360x1350 mm Drive roller for G60 cross...

 Open the catalog to page 10

Compatible spare parts for Grégoire grape harvesters 240 mm bucket for olives belt for Grégoire grape harvesters type G140 Fastening kit for buckets: 1 screw M8 x 30mm + 1 bolt M8 and 1 washer code RICEGRE Pointy copper rivet 4 x 24 mm Hydraulic oil filter 25 micron Stainless steel bucket fixing plate Hydraulic oil filter 10 micron 240 mm stainless steel fastener for NAASGRE cleaner conveyor belt 350 mm stainless steel fastener for 285193G cleaner conveyor belt 240 mm stainless steel fastener for conveyor belt 320 mm stainless steel fastener for conveyor belt 240 mm stainless steel pin for...

 Open the catalog to page 11

Compatible spare parts for Grégoire grape harvesters Eccentric shaft bearing for G60 Eccentric shaft bearing for G70 and G1 Eccentric shaft head bearing Seal washer Eccentric shaft bearing for G60 and G152 Hydraulic filter cartridge for G132 and G152 harvesters. Ø 47 mm. Length: 153 mm Hydraulic filter cartridge for G60 harvester. Ø 56 mm Length:170 mm code 387150G Ref. original code: 387150 Floating shaft

 Open the catalog to page 12