1255 TR
69Pages

1255 TR Pull Type Pneumatic Granular Applicator Valmar Airflo Inc. Box 100 Elie, MB ROH OHO Phone (204) 353-2782 Issue Date: March 2001 FAX (204) 353-2864

Table of Contents ItemPage Serial Number Location 3 Printing Date: December 2009

Warranty VALMAR VALMAR WARRANTY All Valmar products are warranted for one year against defects in materials and workmanship and to perform according to specifications when such products are properly assembled, installed, used and maintained. Valmar warrants that its manufactured parts will be as specified and will be free from defects in material and workmanship. Valmar's liability under this warranty shall be limited to one of the following: 1. Repair or replacement of the defective part at our discretion. 2. Granting of a reasonable allowance providing action of dealer has been approved...

VALMAR Serial Number Location VALMAR Serial Number Location Your Valmar applicator has a model and serial number to clearly identify it. Always give your dealer the Model Number and Serial Number of your machine when ordering parts or requesting service information. Mark the model and serial numbers in the spaces provided for easy reference. Applicator Serial Number The Serial Number Plate is located on the rear inside panel of the hopper as shown in the photo below. Model No. Serial No.

VALMAR Introduction Congratulations on your choice of a Valmar applicator for your farming operation. This equipment has been designed to meet the needs of a discerning agricultural industry for the pneumatic application of fertilizer and granular herbicide products. Safe, efficient and trouble-free operation of your applicator requires that you and all who operate or maintain this machine read and understand all information contained in this Operator's Manual. This SAFETY ALERT SYMBOL indicates important safety messages in this manual. When you see this symbol be alert to the possibility...

VALMAR Safety Read Operator’s Manual ALL OPERATORS must read and understand the Operator’s Manual before working with the applicator. Review the Operator’s Manual and safety decals of this machine before each season of use. The Safety Alert Symbol is on all safety decals on your Valmar applicator. When you see the symbol on a safety decal, follow the instructions to avoid injury or death. Signal Words Note the use of the words DANGER, WARNING and CAUTION on the safety decals. Each signal word denotes a different type of hazard as shown: A SPECIFIC HAZARD OR UNSAFE PRACTICE WHICH COULD...

Safety VALMAR 4. Ensure all guards and shields are in place before operating the applicator. 5. Do not allow riders on the applicator. 6. Ensure that the safety chains are connected to the towing vehicle at all times. Granular Chemical Safety Some granular products are more harmful than others. Do not take a chance. Read and strictly follow the instructions found on the product container or package. To avoid the possibility of burns, lung damage or eye irritation: 1. Wear gloves and safety goggles. 2. Avoid contact with skin and eyes. 3. Avoid breathing dust or fumes. Wear a dust mask or...

VALMAR Safety Decals Safety Decals Keep safety decals clean and legible at all times. Replace decals that are missing or have become illegible. Safety decals or signs are available from the Valmar parts department. Safety Decal Installation • Be sure installation area is clean and dry. 2 • Decide on the exact position before you remove the backing paper. • Remove the smallest portion of the backing paper. • Align the decal over the specified area and carefully press the small portion of the decal in place. • Small air pockets can be pierced and smoothed out. Good safety practice requires...

Safety Decals VALMAR

VALMAR Operation 4 - Operation Your 1255 TR Pull Type applicator is designed to efficiently broadcast fertilizer, granular pesticides and seed. The illustration below demonstrates how the system works. The 1255 TR Pull Type uses either a gas engine or hydraulically powered fan to blow air through a manifold. The air accelerates as it passes through the venturis, picking up product conveyed into the venturis by the metering roller. The product is then blown out through the delivery hoses and deflectors along the booms. The booms can be set up for either a 16 or 20 foot broadcast width or...

Operation VALMAR Pre-Operation Checklist Before operating the applicator and each time thereafter, inspect the following areas. If adjustments are necessary, see the Adjustments and Service chapter of this manual for further information. 1. Ensure that the electrical connections between the tractor and the implement harness are sound. 2. Inspect the hopper and metering system for debris. Clean if necessary. 3. Make sure that all guards and shields are in place. 4. Ensure that all tires are at the correct pressure as noted in Chapter 5. 5. Ensure that any hydraulic lines are...

VALMAR Operation VALMAR Operation Proper fan speed for most applications will be 17 inches of water column pressure. For high rate applications, water column pressure may have to be increased to over 20 inches. The fan speed may be measured directly by inserting a tachometer into the end drill of the fan shaft. The fan speed should be approximately 4300 rpm. The 1255 TR Pull Type has two different fan drive options: a hydraulically driven fan, and a gas engine driven fan. Gas Engine Fan Drive The 1255 TR Pull Type can be equipped with a 9 horsepower Honda engine. Refer to the Honda Owner’s...

Operation VALMAR

VALMAR Operation 1. Release the clip on the gearbox speed shifter and lift. 2. Move the range shift lever to the “A" or “B” position. Check for proper alignment of the top and bottom gear clusters. Lock the speed shifter into position by pushing down on the clip. Maximum Speeds If the applicator has the 26X12.00-12 flotation tires installed, the applicator should not be towed faster than 15 mph. If the applicator has the P195/60R trailer tires installed, it can be safely towed at highway speeds. Speed Selection (Fig. 4-9) 1. Release the clip on the gearbox speed shifter and lift. 2. Slide...