Extractos del catálogo
User Manual MachineryGuide GPS Guidance System System setup Read the whole manual before using the product and keep it for later reference
Abrir la página 1 del catálogoParts of the Guidance System GPS/GLONASS antenna Bluetooth GNSS Receiver Antenna Cable DC-USB Cable Tablet Mount Software Installation Installation steps Software Updates First Steps Options menu General settings menu Units, Gauges to display and Overlap Option menu Session handling, GPS source and Display menu Size and Alignment menu Guidance mode menu Advanced Guidance mode menu Language settings
Abrir la página 2 del catálogoFont size settings Data menu Field handling menu Create New Field menu Session handling Reference Lines menu Obstacles menu Prescription map handling menu Data Synchronization menu
Abrir la página 3 del catálogoParts of the Guidance System Part name GPS/GLONASS antenna Bluetooth GNSS receiver Antenna cable DC-USB cable Car charger, 3-points charger and 2-wire charger Tablet mount Android device MachineryGuide Android application
Abrir la página 4 del catálogoGPS/GLONASS antenna The Antenna has to be mounted to the highest part of the agricultural machine, and must not be obscured in order to achieve the best accuracy. There are several antenna options available for the MachineryGuide application: SM1 antenna Specifications: ● Frequency: 1575MHz ~ 1615MHz ● VSWR: 1.3 @ 1580MHz ● Bandwidth: 43MHz ● Polarization: RHCP ● Antenna gain: 27dB ● Dimensions: 37.5mm x 34.5mm x 12.5mm ● Connection: SMA ● RF cable: RG174, 2.5m ● Magnetic bottom DM1 antenna The DM1 antenna has high gain (40 dB) and multipath error rejection. Specifications: ● Frequency:...
Abrir la página 5 del catálogoDM1 Antenna Console The DM1 antenna can be installed with a magnetic console. The antenna goes to the top of the holder. The consol with the antenna should be installed to the top of the agricultural machine. It is very important to place it on the highest part of the vehicle, and to ensure that it is not covered, because this is indispensable to achieve the correct pass-to-pass accuracy. CM1 antenna The CM1 antenna has high gain (40 dB) and multipath error rejection. Specifications: ● Frequency: 1574 MHz ~ 1606 MHz ● Bandwidth: 31 MHz (1dB) ● Polarization: RHCP ● Antenna gain: 40 dB ●...
Abrir la página 6 del catálogoCM2 patch antenna The CM2 Bluetooth receiver can be used with patch antenna as well. Specifications: ● Frequency: 1164 MHz ~ 1300 MHz, 1520 ~ 1615 MHz ● Band width: 31 MHz (1dB) ● Polarization: RHCP ● Antenna gain: 40 dB ● Dimensions: 60 mm x 90 mm x 23 mm ● Connection: SMA ● Manufacturer: u-blox CM1/CM2 antenna mount The CM1/CM2 antenna is fixed in place with the help of the magnetic based mount. The mount should be fixed to the highest point of the machine being used with the CM1 or CM2 antennas. It is important that the antenna is not being covered or blocked, since this can decrease the...
Abrir la página 7 del catálogoSM1 Bluetooth GNSS Receiver Specifications: ● GPS-, GLONASS-, SBAS-, QZSS-signals ● 10 Hz update rate ● Absolute accuracy: 2.5 m CEP ● Absolute accuracy with SBAS correction: 2.0 m ● Pass-to-pass accuracy with SBAS correction:10-20 cm ● Speed accuracy: 0.1m/s ● Hot start TTFF open sky: 29 mp ● Cold start TTFF open sky:30 mp ● Sensitivity: -161 dBm ● Bluetooth device name: MachineryGuide BT-REC-V2.3 SM1 When the Receiver is turned on, after two-three minutes of initialization time (depends on the satellite coverage) the Receiver starts to provide submeter level pass-to-pass accurate position...
Abrir la página 8 del catálogoCM1 Bluetooth GNSS Receiver Specifications: ● Uses GPS, GLONASS, SBAS, QZSS signals ● 10 Hz update rate ● Absolute position accuracy 1 cm CEP ● Relative (pass-to-pass) accuracy: 2 cm ● Speed accuracy 0.1m/sec ● Warm start TTFF under open sky 29 sec average ● Cold start TTFF under open sky 30 sec average ● Tracking sensitivity -165 dBm ● Bluetooth version: 2.0 ● Bluetooth device name: ● MG BT-REC-V2.3 CM1 15-20 minutes after starting (depending on the satellite coverage) the receiver unit begins to transmit centimeter accurate position data. CM2 Bluetooth GNSS Receiver Specifications: ●...
Abrir la página 9 del catálogoNODE Central Unit Bluetooth GNSS Receiver Specifications: ● Operates the following signals: GPS, L1C6a L2C, GLO L1OF L2OF, GAL E1B/C E5b, BDS B1I B2I, QZSS L1C/A L2C ● 20 Hz update rate ● Absolute accuracy: 1 cm CEP ● Pass-to-pass accuracy: 2 cm ● Speed accuracy: 0.1 m/sec ● Hot start TTFF, on average, under clear sky is 29 seconds ● Cold start TTFF, on average, under clear sky is 30 seconds ● Sensitivity - 165 dBm ● Bluetooth version: 2.0 ● Name of Bluetooth device: MG-Node 2-3 minutes after starting (depending on the satellite coverage) the receiver unit begins to transmit centimeter...
Abrir la página 10 del catálogoDC-USB Cable The DC-to-USB cable provides power to the Bluetooth GNSS Receiver. There are three types of cables available for the Receiver: A DC-to-USB cable with DC plug only on one end for the Bluetooth GNSS Receiver. Specifications: ● Length: 2.5 m ● Plug type: 2.1 mm DC plug A DC-to-USB cable with a DC plug for the Bluetooth GNSS Receiver and a standard car charger plug. Specifications: ● Length: 2 m ● Plug type: 2.1 mm DC plug A DC-to-USB cable with a DC plug for the Bluetooth GNSS Receiver and a 3-point charger plug. Specifications: ● Length: 2 m ● Plug type: 2.1 mm DC plug Tablet...
Abrir la página 11 del catálogoSoftware Installation Internet connection is required for downloading and activating the application. The software (APK file) can be downloaded from website machineryguide.hu/downloads, from the following link: machineryguideapp.com/en/releases a. It is recommended to reach the website directly from your tablet/smartphone, since this way the APK file is installed right away when tapping the download link. b. When the installer file (APK file) is downloaded to your computer, copy the file to your Android device. For this, connect your device to the computer as a media device with a...
Abrir la página 12 del catálogoAfter installation, activate your software. Click on ”Licence” button, then write in your 8 character long code given by your distributor. (In case you bought only the software, you will receive it in an e-mail, otherwise the code is found in the product box.) After entering the code, the ”Licence” button on the main window will change to ”Start” button and you will be able to use the software without any restrictions. Software Updates Software updates are available on this link: machineryguide.hu/downloads. Installing a software update is very similar to the installation of the original...
Abrir la página 13 del catálogoTodos los catálogos y folletos técnicos MachineryGuide
-
GPS Guidance System Starting a job
36 Páginas
-
CM1 PACKAGE ASSEMBLY GUIDE
2 Páginas
-
AutoSteer Assisted Steering Unit
24 Páginas
-
Ordering Guide 2020
24 Páginas
-
Product Catalogue 2020
15 Páginas
-
Product Catalog 2018
9 Páginas
-
MachineryGuide Flyer
2 Páginas