TA6
1 / 10Páginas

Product Segments • Comfort Motion TiMOTION's TA6 series linear actuator is designed for lift applications like recliners, lifting chairs and movie theater seating. Its right-angle design reduces noise and allows for fitment into most applications. Industry certifications for the TA6 linear actuator include EMC and RoHS. In addition, the TA6 is available with optional Hall sensors for position feedback. It can also be used where freewheeling push only functionality is desired. General Features Max. load Retracted length Output signals Hall sensors Freewheeling push only, safety nut Operational temperature range

Standard Dimensions

Load and Speed CODE Self Locking Force (N) Motor Speed (2600RPM, Duty Cycle 10%) C Motor Speed (3400RPM, Duty Cycle 10%) L Motor Speed (3800RPM, Duty Cycle 10%) X Note 1 Please refer to the approved drawing for the final authentic value. 2 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 3 Operational temperature range at full performance: +5°C~+45°C 4 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the...

Motor Speed (2600RPM, Duty Cycle 10%) Speed vs. Load 40.0 Performance Data (24V DC Motor)

Motor Speed (3400RPM, Duty Cycle 10%) Speed vs. Load 40.0 35.0 30.0 Performance Data (24V DC Motor)

Motor Speed (3800RPM, Duty Cycle 10%) Speed vs. Load 45.0 40.0 35.0 Performance Data (24V DC Motor)

Rear Attachment (mm) See page 9 1 = Plastic, U clevis, slot 6.1, hole 10.2 Front Attachment (mm) See page 9 1 = Punched hole on inner tube + plastic cap, without slot, hole 10.2, with plastic bushing 2 = Punched hole on inner tube + plastic cap, without slot, hole 12.2 3 = Plastic, U clevis, slot 8.2, depth 20.2, hole 10.2, for load push < 4000N & pull < 2500N 4 = Plastic, U clevis, slot 8.2, depth 20.2, hole 12.2, for load push < 4000N & pull < 2500N 5 = Punched hole on inner tube, without slot, hole 10.2, with plastic bushing Special Functions for Spindle SubAssembly Functions for Limit...

TA6 Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B+C = Y 2. Retracted length needs to ≥ Stroke + Y A. Front Attachment C. Front Attachment V.S Special Function Front Attachment B. Load V.S. Stroke Stroke (mm)

TA6 Ordering Key Appendix Rear Attachment (mm) 1 = U clevis plastic, slot 6.1, hole 10.2 24.5 4 = Plastic, U clevis, slot 8.2, depth 20.2, hole 12.2, for load push < 4000N & pull < 2500N 8=A luminum casting, U clevis, slot 6.2, depth 17.0, hole 12.2 7 = Aluminum casting, U clevis, slot 6.2, depth 17.0, hole 10.2 ø26 6 = Punched hole on inner tube, without slot, hole 12.2 5 = Punched hole on inner tube, without slot, hole 10.2, with plastic bushing 3 = P lastic, U clevis, slot 8.2, depth 20.2, hole 10.2, for load push < 4000N & pull < 2500N 2 = Punched hole on inner tube + plastic cap,...

TA6 Ordering Key Appendix Functions for Limit Switches Wire Definitions CODE extend (VDC+) retract (VDC+) extend (VDC+) retract (VDC+) extend (VDC+) upper limit switch retract (VDC+) lower limit switch extend (VDC+) upper limit switch medium limit switch retract (VDC+) lower limit switch B = Y cable (For direct cut system, non water proof, non anti pull) L3 Cable length for direct cut system (mm) P = Molex 8P, 90° plug, without anti-clip Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to...