Extraits du catalogue
UC 300 UNIVERSAL COUNTER USER’S MANUAL NR.1111-EN
Ouvrir le catalogue en page 1This product complies with EMC requirements as defined by Directives 2004/108/CE and successive modifications in accordance with standard EN ISO 14982 applied Manufacturer Address : MC Elettronica S.r.l. : Via E. Fermi, 450/486 Fiesso Umbertiano (ROVIGO) – ITALY Tel. +39 0425 754713 Fax +39 0425 741130 E-mail: mcstaff@mcelettronica.it Internet: www.mcelettronica.it Manual code Issued Edition MC elettronica S.r.l. is not obliged to give notice of any further modifications of the product. The information given in this manual does not allow unauthorized personnel to tamper the product in any...
Ouvrir le catalogue en page 2! CHARGE FOR 8 HOURS BEFORE USING User’s manual
Ouvrir le catalogue en page 31. Rules and general warning 1.1 Introduction This manual gives all the specific information that you need for a proper use of the equipment. After buying the instrument, read the manual carefully and refer to it any time you have doubts on how to use the equipment or when you have to carry out maintenance operations. Keep the manual on the machine. If this is not possible, keep it ready to hand. ALL RIGHTS RESERVED. THIS MANUAL IS INTENDED FOR CUSTOMERS ONLY. ANY OTHER USE IS FORBIDDEN. User’s manual
Ouvrir le catalogue en page 5SUBJECT OF THE GUARANTEE: the guarantee is applied to the product and to those parts which are marked with the serial number or any other identification number used by MC Elettronica; HOW LONG THE GUARANTEE IS EFFECTIVE: MC elettronica S.r.l. guarantees the UC 300 for a period of 1 year from the manufacturing date (printed on the identification label which is to be found on the rear side of the equipment) and also accessories. The guarantee covers the product and any repair carried out within the agreed terms. This guarantee does not apply in the event of: • accidental damage; • improper...
Ouvrir le catalogue en page 62. General description The UC 300 Universal Counter is powered by a rechargeable battery and stores all the main functions of a hectare counter in a small container which can be installed easily on any public works vehicle. You can choose between metric and imperial units of measurement to calculate area, distance and speed. The UC 300 Universal Counter can also count the working hours when the machine is running. Displayed on the screen are: 1) independent total counter for surface area (in hectares or acres, in units of 10 m² or 0.001 acres) 2) independent partial counter for surface area...
Ouvrir le catalogue en page 7(*) = Maximum input frequency 35Hz magnetic sensor User's manuale
Ouvrir le catalogue en page 8User's manual
Ouvrir le catalogue en page 95. Operation When the counter is started up for the first time (or after the battery is charged after having run down completely), the total area counter is shown on the display. The UC 300 is set by default to show metric measurements: the area is given in hectares, the speed in km/h and the distance covered in metres. The initial sequence is, therefore: Pressing the “select” button during operation shows the next measurement on the display, as follows After selecting a measurement it is possible to reset it by pressing and holding the "reset" button for 3 seconds (with the exception of...
Ouvrir le catalogue en page 10the residual autonomy of the UC 300 before it turns off completely is limited and will depend also on use. If the battery runs down completely and the UC 300 turns off, some of the data may be lost (refer to the previous section); to charge the battery, connect the cable with the jack connector (provided) to a 12V battery: Do NOT use car battery charging devices. The charging process generally takes about 10 hours, while the autonomy between a charging cycle and the next is about 2.5 years (although this depends on the extent and conditions of use); it is not necessary for the speed sensor...
Ouvrir le catalogue en page 11Programming of this parameter is very important to the work in hand and to the programmable parameters. You need to select either the metric or imperial unit of measurement; you then only need to program the parameters of the UC 300 for the chosen unit of measurement. User's manuale
Ouvrir le catalogue en page 128.3 Automatic programming of parameter “C” (puises of the speed sensor) It is possible to program parameter C automatically: after entering the programming phase as instructed above, and with “C” shown on the display followed by the value currently programmed, press both the “+” and “-” buttons at the same time and the following appears on the display At this point, travel 100 metres (or 330 feet) in the machine and the number will increase automatically on the display. After covering this distance, press the "Prog" button to confirm the data. It is advisable to repeat this operation at...
Ouvrir le catalogue en page 138.4 Programming parameter “L” (working width) This parameter is the working width of the machine in metres (or feet). Enter the programming phase as described above and edit the value with the “+” and “-” buttons; pressing and holding either button will speed up the editing process. After setting the required value, press "Prog" to confirm and exit the programming phase. Hect P'°g. Reset\ with “Un” = 1 User’s manuale
Ouvrir le catalogue en page 149. Maintenance This chapter gives instructions on how to carry out ordinary and extraordinary maintenance. Ordinary maintenance refers to those operations which must be carried out periodically. As they do not require specific skills, they can be carried out by the users (operators etc.). Extraordinary maintenance refers to unforeseeable operations due to mechanic or electric failures. They require specific technical skills, so they should be exclusively carried out by qualified personnel (maintenance personnel etc.) 9.1 Ordinary maintenance Ordinary maintenance consists in cleaning the...
Ouvrir le catalogue en page 15WARNING: THIS PRODUCT CONTAINS TIN AND LEAD. IT MUST BE DISPOSED OF AT THE END OF ITS LIFE CYCLE AT THE DESIGNATED DISPOSAL FACILITIES OR DELIVERED DIRECTLY TO MC ELETTRONICA SRL (ITALY). User's manuale
Ouvrir le catalogue en page 16Electronic equipments for agricultural www.mcelettronica.it
Ouvrir le catalogue en page 20Tous les catalogues et fiches techniques (PDF) MC Elettronica srl
-
BLOCKAGE MONITOR COUNTER SYSTEM
56 Pages
-
KIT HYDRA 590 and CB9
40 Pages
-
GLM KIT
36 Pages
-
SOLID CONTROL MCK 2000
48 Pages
-
HIGH-TECH SYSTEMS
8 Pages
-
AIR VALVE LB 100 NG
1 Pages
-
MAXISEEDER PHOTOCELL
1 Pages
-
TINYSEEDER PHOTOCELL
1 Pages
-
UNISEEDER PHOTOCELL
1 Pages
-
SIEVE SENSOR
1 Pages
-
DORADO MX System
2 Pages
-
HYDRA 590 - HYDRA ISOBUS
20 Pages
-
ECU BRIDGE
4 Pages
-
PRO - SEEDER
4 Pages
-
GLM / GLM
8 Pages
-
Row Seeding
94 Pages
-
Precision seeding
74 Pages
-
Custom Creations
4 Pages