WRM-M 145 / 200
1 / 21ページ

matev GmbH Nürnberger Str. 50 90579 Langenzenn, Germany T +49 9101 9087-0 F +49 9101 9087 -20 info@matev.eu www.matev.eu Assembly Manual WRM-M 145 / 200

This manual explains the assembly of the WRM-M 145 and 200 weed brush. The machine is available in two versions. In this regard, only the arm assembly and the drive assemblies differ. Everything else is the same. The manual deals with the following:  Setup of the steel construction  In section 1.2 the tightening torque of screw connections and the grub screws in taper-lock bushes is shown  Setup of the belt drive and the correct arrangement for rotational speed and direction of rotation  The various hydraulic designs  The arrangement of the pictograms  The machine must be greased...

1. Setup of the steel construction without belt drive 1.1. Drawings and assemblies Description Attachment bracket, assembly Arm, assembly Pivot bracket, assembly Holder, assembly Short arm Description Arm, assembly Long arm Description Arm, assembly Splash guard Description Splash guard Part number File name Part number File name Part number File name Part number File name See the current spare parts lists on T-drive

Unless otherwise specified in the drawings, tighten screws to the torque shown in the tables: 1.2.1. Table for threaded unions with standard thread 1.2.2. Table for taper-lock bushes

2. Structure – belt drive with direction of rotation and speed 2.1. Direction of rotation The gearbox determines the direction of rotation. Turning over the gearbox changes the direction of rotation. Shown here for operation on the right side of the vehicle. If the machine is intended for operation on the left side of the vehicle, the arrangement is precisely the opposite. Install arrangement for CCW For driving operation on the left side the shaft must turn in the opposite direction. Page 5 of 21 C:\Users\kwo\Desktop\MA_WRM_145_200_MLU_DE_Rev_1-0-EN.docx

Belt drive 2000 rpm For all belt drives the belt pulleys must be aligned to the same height. The screws of the taper-lock bushes must be tightened with the correct torque for the size. At the end of installation, you must check the direction of rotation. Description Belt pulley SPA 212-04, TP 3020 Belt pulley SPA-Ø100-4-TP1610 V-belt XPA 2240 Ld Description Belt pulley SPA 212-04, TP 3020 Belt pulley SPA-Ø100-4-TP1610 V-belt XPA 2800 Ld

Short arm: Item Quantity 1 2 2 4 Long arm: Item Quantity 1 2 2 4 Description Belt pulley SPA 212-04, TP 3020 V-belt SPA 2432 Ld Description Belt pulley SPA 212-04, TP 3020 V-belt SPA 2982 Ld

3. Hydraulic variants 3.1. Tractor has only one hydraulic circuit, pivot brush head mechanically WRM-M 145 Hydraulic kit, assembly WRM-M 200 Hydraulic kit, assembly

3.2. Variant 2 – tractor has two hydraulic circuits, pivot brush head hydraulically WRM-M 145 Hydraulic kit, assembly WRM-M 200 Hydraulic kit, assembly

3.3. Variant 3 – tractor has 1 hydraulic circuit, pivot brush head hydraulically WRM-M 145 Hydraulic kit, assembly WRM-M 200 Hydraulic kit, assembly

5. Pictogram arrangement The pictograms must be arranged as shown in the photos. The surfaces must be thoroughly cleaned beforehand, to enable good adhesion. Use stickers that are appropriate for the drive set. 1000 rpm or 2000 rpm

Check direction of rotation and rotational speed Check the function of the hydraulic cylinders. (Is something interfering, leaks?) Check the hydraulics. Is the switching logically correct? Leaks? Function of the electric control system