1665
1 / 80ページ

1665 Pneumatic Inoculant Applicator OPERATOR'S MANUAL Issue Date: April 2003 Valmar Airflo Inc. Box 100 Elie, MB ROH OHO Phone (204) 353-2782 FAX (204) 353-2864 Email: valmar@valmar.com

VALMAR Table of Contents Item Page Serial Number Location 3 Printing Date: February 20<4

Warranty VALMAR VALMAR WARRANTY All Valmar products are warranted for one year against defects in materials and workmanship and to perform according to specifications when such products are properly assembled, installed, used and maintained. Valmar warrants that its manufactured parts will be as specified and will be free from defects in material and workmanship. Valmar’s liability under this warranty shall be limited to one of the following: 1. Repair or replacement of the defective part at our discretion. 2. Granting of a reasonable allowance providing action of dealer has been approved...

VALMAR Serial Number Location VALMAR Serial Number Location Your Valmar applicator has a model and serial number to clearly identify it. Always give your dealer the Model Number and Serial Number of your machine when ordering parts or requesting service information. Mark the model and serial numbers in the spaces provided for easy reference. Applicator Serial Number The Serial Number Plate is located on the front right-hand inside panel of the hopper as shown in the photo below. Model No. Serial No.

Serial Number Location VALMAR

VALMAR Safety Read Operator’s Manual ALL OPERATORS must read and understand the Operator's Manual before working with the applicator. Review the Operator’s Manual and safety decals of this machine before each season of use. The Safety Alert Symbol is on all safety decals on your Valmar applicator. When you see the symbol on a safety decal, follow the instructions to avoid injury or death. Signal Words Note the use of the words DANGER, WARNING and CAUTION on the safety decals. Each signal word denotes a different type of hazard as shown: WARNING A SPECIFIC HAZARD OR UNSAFE PRACTICE WHICH...

Safety_ VALMAR 4. Ensure all guards and shields are in place before operating the applicator. 5. Do not allow riders on the applicator. 6. Operators of this equipment should be a minimum of 16 years of age. Granular Chemical Safety Some granular products are more harmful than others. Do not take a chance. Read and strictly follow the instructions found on the product container or package. To avoid the possibility of burns, lung damage or eye irritation: 1. Wear gloves and safety goggles. 2. Avoid contact with skin and eyes. 3. Avoid breathing dust or fumes. Wear a dust mask or respirator as...

VALMAR Safety Decals Safety Decals Keep safety decals clean and legible at all times. Replace decals that are missing or have become illegible. Safety decals or signs are available from the Valmar parts department. Safety Decal Installation • Be sure installation area is clean and dry. • Decide on the exact position before you remove the backing paper. • Remove the smallest portion of the backing paper. • Align the decal over the specified area and carefully press the small portion of the decal in place. • Small air pockets can be pierced and smoothed out. Good safety practice requires that...

Safety Decals

VALMAR Operation 4 - Operation Your 1665 Innoculant applicator is designed to efficiently broadcast granular pesticides and seed. The illustration below demonstrates how the system works. The 1665 uses a hydraulically powered fan (or an air seeder fan) to blow air through a manifold. The air accelerates as it passes through the venturis, picking up product conveyed into the venturis by the metering wheels. The product is then blown out through injectors into the distribution towers on the implement. All metering components are driven either by a mechanical ground drive system...

Operation VALMAR Operation VALMAR Before operating the applicator and each time thereafter, inspect the following areas. If adjustments are necessary, see the Adjustments and Service chapter of this manual for further information. 1. Ensure that any electrical connections between the tractor and the implement harness are sound. 2. Inspect the hopper and metering system for debris. Clean if necessary. 3. Make sure that all guards and shields are in place. 4. Ensure that all tires are at the correct pressure as noted in Chapter 5. 5. Ensure that any hydraulic lines are securely connected to...

VALMAR Operation tractor's operator’s manual to see which system you have. Set up your hydraulic fan drive accordingly: Closed Center Hydraulics 1. Set the Valmar flow control valve at the maximum setting of “10". 2. Engage the tractor hydraulics. 3. Adjust the fan speed using the adjustable flow control valve on the tractor. If surging occurs, slowly close the valve until the surging stops. Readjust the fan speed. If surging still occurs, see the Options section for a kit to solve the problem. Open Center Hydraulics 1. Set the Valmar flow control valve at the closed setting of “0”. 2....

Operation VALMAR Range and Speed Selection (Fig. 4-9) 1. Release the clip on the gearbox speed shifter and lift. 2. Move the range shift lever to the "A" or “B” position. Check for proper alignment of the top and bottom gear clusters. Lock the speed shifter into position by pushing down on the clip. Speed Selection (Fig. 4-9) 1. Release the clip on the gearbox speed shifter and lift. 2. Slide the speed shifter sideways to the correct (numbered) detent position. Drop the speed shifter into the detent slot. 3. Rotate the gears manually to ensure complete engagement. Lock the speed shifter...

VALMAR Operation gallons per minute for your remotes, such as an LED readout or numbered dial, set your applicator as follows: 1. Refer to the product flow rate charts in Chapter 5. 2. Find the desired product application rate at the desired ground speed. 3. Find the hydraulic oil flow rate that corresponds to the product application rate. 4. Set your tractor's flow controller to the correct hydraulic oil flow rate. You may need to run the engine rpm at full operating speed and engage the hydraulic fan drive to set the oil flow rate accurately. 5. Perform a calibration as instructed...