Exhibit with us
*myagriexpo  
English
  1. Catalogs
  2. Ace Pump Corporation
  3. FMC-HYD

FMC-HYD

FMC-HYD
1 / 2 PagesView full catalog

FMC-HYD

Product catalog summary
Performance Specifications:
The FMC-HYD hydraulic motor-driven centrifugal pump features a suction size of 1-1/4” and a discharge size of 1”. It supports different motor requirements: the 204 motor requires 4 GPM (15.1 LPM), the 210 motor requires 10 GPM (37.9 LPM), and the 310 motor requires 16 GPM (60.6 LPM) hydraulic flow. An integral needle valve can bypass up to 9 GPM (34 LPM) on open center systems. The pump is equipped with a standard Viton® carbon/ceramic seal or an optional severe duty silicon carbide mechanical seal. It also features a chemical-resistant Valox® impeller or an optional cast iron impeller, along with a stainless steel shaft and wear ring.
Performance Chart:
The chart illustrates the relationship between pressure and flow rate for different oil flow rates (3.0, 3.4, 3.8, and 4.3 GPM). The maximum shutoff pressure is 100 psi.
Dimensions:
The dimensions are provided in both inches and millimeters, ranging from 1.5 inches (38.1 mm) to 12.5 inches (317.5 mm).
Parts List:
A detailed parts list is provided, including part numbers, descriptions, and quantities required. Key components include pipe plugs, volute, nuts, washers, impellers, seals, mounting frames, cap screws, snap rings, ball bearings, shafts, hydraulic motors, and various adapters and valves. Optional parts and repair kits are also listed.
Contact Information:
Ace Pump Corporation is located at 1650 Channel Avenue, Memphis, TN 38113. Contact can be made via phone at 901-948-8514 or fax at 901-774-6147. More information is available on their website www.AcePumps.com.
See more

Catalog excerpts

FMC-HYD-1

Hydraulic Motor Driven Centrifugal Pump FMC-HYD -204 motor requires 4 GPM (15.1 LPM) hydraulic flow on PC Closed and Open Center Systems -210 motor requires 10 GPM (37.9 LPM) hydraulic flow on LS Closed and Open Center Systems -310 motor requires 16 GPM(60.6 LPM) hydraulic flow on Large Open Center Systems  Integral Needle Valve bypasses up to 9 GPM (34 LPM) on Open Center Systems  Standard Viton ® Carbon/Ceramic seal or Optional Severe Duty Silicon Carbide Mechanical Seal  Chemical Resistant Valox® or Optional Cast Iron Impeller  Stainless Steel Shaft and Wear Ring Maximum Shutoff Pressure 100 psi Valox® is a registered trademark of GE Plastics. Viton® is a registered trademark of DuPont

 Open the catalog to page 1
FMC-HYD-2

Ace Pump Corporation • 1650 Channel Avenue • Memphis, TN 38113 www.AcePumps.com • Phone: 901-948-8514 • Fax: 901-774-6147

 Open the catalog to page 2

All Ace Pump Corporation catalogs and technical brochures

  1. FMC-150-HYD-206
    FMC-150-HYD-206

    2  Pages

  2. Product Catalog
    Product Catalog

    28  Pages

  3. FMC 200
    FMC 200

    2  Pages

  4. FMC 150
    FMC 150

    2  Pages

  5. PTOC series
    PTOC series

    4  Pages

  6. FMC-75-HYD
    FMC-75-HYD

    2  Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.