Product Catalog
28Pages

PRODUCT CATALOG

APPLICATION INFORMATION SPRAYER PLUMBING SUGGESTIONS The primary goal when plumbing a sprayer pump is to route liquid from the pump to the spray boom with minimum restriction. Minimizing restrictions is necessary for achieving the pump's maximum rated capacity. • Hoses should be the same size as the pump's suction and discharge ports. • Install a pressure gauge and valve on the discharge side of the pump for the purpose of measuring the SHUT-OFF pressure. USEFUL FORMULAS __40 x GPM (per Nozzle) GPA = Gallons Per Acre MPH = GPM = Gallons Per Minute W = • A minimum number of elbows,...

PUMP SELECTION WORKSHEET Visit our web site at www.AcePumps.com to use an automated version of this worksheet. Fill in the application information: Application Rate (GPA) Speed (MPH) Nozzle Spacing (inches) x ____________________ = ____________________ ‫____________________ = 0495 נ‬ 3 Identify the flow required for AGITATION (typically 5% of tank’s capacity): Note: Use of jet agitators may reduce flow needed for agitation. 4 Then add: Boom Flow (GPM) = Total Pump Flow (GPM) required 5 Adjust for heavier fluids: Total Pump Flow (GPM) Specific Gravity Conversion Factor See Specific Gravity...

General Advantages Ace developed the first hydraulic motor driven pump at the request of John Deere in 1969. Ace continues to develop a comprehensive range of reference materials and hydraulic accessories allowing the pumps to be effectively applied on the full range of hydraulic systems. Centrifugal pump design provides good resistance to abrasive solutions and extra flow for agitation. All hydraulic driven pumps are equipped with a stainless steel shaft and wear ring for excellent corrosion resistance. The advantages of ACE hydraulic motor driven pumps are: • MOUNTING VERSATILITY: The...

Features • The farm industry standard since 1969. • The 202 and 203 motors require 2 GPM (7.6 LPM) and 3 GPM (11.4 LPM) hydraulic fluid input. Recommended for engineered systems with limited oil flow. • The 204 motor requires 4 GPM (15.1 LPM) maximum hydraulic fluid input. Recommended for: - Pressure Compensating Closed Center Systems - Open Center Systems up to 13 GPM (49.2 LPM) using internal needle valve bypass • The 210 motor requires 10 GPM (37.9 LPM) maximum hydraulic fluid input. Recommended for: - Load Sensing Closed Center Systems - Open Center Systems up to 17 GPM (64.4 LPM) using...

ISO SERIES HIGH PERFORMANCE Features • F model equipped with NPT ports and industry standard flanged connections. • FS model constructed of 316 stainless steel with NPT ports and industry standard flanged connections. • SP model is self-priming making it perfect for load and spray applications. • Provides higher pressure and greater volume for applications with large tanks and longer spray booms. • The 206 motor requires 7 GPM (26.5 LPM) maximum hydraulic fluid input and fits virtually all tractor hydraulic systems. Recommended for: - Pressure Compensating Closed Center Systems - Load...

Features • Ideal for spraying, large tank agitation, liquid transfer, and spray - transfer combinations. • F model equipped with industry standard flanged connections. • 200SS model has 316 stainless steel wet end including impeller (Jj), volute, and seal plate. • The 210 motor requires 10 GPM (37.9 LPM) maximum hydraulic fluid input. Recommended for: - Pressure Compensating Closed Center Systems - Load Sensing Closed Center Systems - Open Center Systems up to 17 GPM (64.4 LPM) using internal needle valve bypass • The 304 motor requires 13 GPM (51.1 LPM) maximum hydraulic fluid...

HIGH PERFORMANCE Features • Severe duty silicon-carbide shaft seal (SC) standard with o-ring seat for improved survivability. • 316 stainless steel housings with NPT ports and industry standard flanged connections. • Larger bearings for extended life. • Provides higher pressure and greater volume for applications with large tanks and longer spray booms. • The 206 motor requires 7 GPM (26.5 LPM) maximum hydraulic fluid input and fits virtually all tractor hydraulic systems. Recommended for: - Pressure Compensating Closed Center Systems - Load Sensing Closed Center Systems - Open Center...

General Advantages Ace's MAX Series pumps were designed from the ground up for today's demanding applications. Each model is engineered for maximum reliability and performance. A durable e-coat finish provides extra corrosion resistance on all surfaces inside and out. The 4000 psi high efficiency pressure plated gear motors provide higher output with less oil flow. The impellers are designed to develop higher pressure at lower shaft speeds. A splined motor to pump shaft connection strengthens the power train while allowing for easy repair and maintenance. Oversized bearings round out the...

WetSeal Technology Ace won an AE50 award for Outstanding Innovations in Product Technology with the first wet seal pump for agricultural spraying in 2009. Since that time, Ace has continued to lead the market in development of this innovative design. Today there are three pump sizes and nine models available which may be customized to fit virtually any application. The WS-650 MAX, 750 MAX and 855 MAX pump models feature our Oasis™ WetSeal Technology. The dual shaft seals run in a pressurized barrier fluid which is specially formulated for seal face lubrication and heat dissipation. The...

Features • The M22 motor requires 18 GPM (68.1 LPM) maximum hydraulic fluid input. Recommended for: - Pressure Compensating Closed Center Systems - Load Sensing Closed Center Systems - Open Center Systems up to 18 GPM (68.1 LPM) • The M25 motor requires 20 GPM (75.7 LPM) maximum hydraulic fluid input. Recommended for: - Pressure Compensating Closed Center Systems - Load Sensing Closed Center Systems - Open Center Systems up to 20 GPM (75.7 LPM) Features • The M30 motor requires 23 GPM (87 LPM) maximum hydraulic fluid input with #6 SAE case drain port and is standard on the 855 MAX...