PANEL SWITCHES Double icon illuminated pushbuttons • bushing Ø 24 or 26 mm • momentary or latching DISTINCTIVE FEATURES Double icon actuator Snap-in and threaded bushing models Large but lightweight Sealed to IP69K (threaded bushing version) ENVIRONMENTAL SPECIFICATIONS • Front panel sealing : - Threaded bushing version : IP69K according to DIN 40050-9 - Snap-in version : IP54 according to IEC 60529 with panel gasket and 2 mm panel thickness • Operating temperature : -40 °C to +75 °C (40 °F to +167 °F) ELECTRICAL SPECIFICATIONS • Max. current/voltage rating with resistive load : - silver contacts (code 2) : 4 A 12 VDC - gold plated contacts (code 4) : 200 mA 12 VDC • Initial contact resistance : 50 mΩ max. • Insulation resistance : 1 GΩ min. at 500 VDC • Dielectric strength : 1,000 Vrms 50 Hz min. • Electrical life at full load : - Momentary models : 1 million cycles (gold plated contacts) 400,000 cycles (silver contacts) - Latching models : 200,000 cycles LED COMPONENT SPECIFICATIONS LED color Forward current A resistor must be series-connected by the user Resistor value = supply voltage - LED forward voltage The company reserves the right to change specificat

PANEL SWITCHES FD series Double icon illuminated pushbuttons • bushing Ø 24 or 26 mm • momentary or latching GENERAL SPECIFICATIONS • Panel thickness : - Snap-in version : 1.5 (.059) to 2 mm (.078) with panel gasket 2 (.078) to 2.5 mm (.885) without panel gasket - Threaded bushing version :1(.039) to 15,5mm (.590) max. • Typical operating force : 8 N ± 2 N • Low level or mechanical life : - Momentary models : 1 million cycles - Latching models : 200,000 cycles WIRING DIAGRAM FICHIER: POLE 2 CFDDEC-P3 ECHELLE: 0.625 LED MATERIALS • Case : PA46 • Actuator : PA12 • Bushing/ bezel : PA66 • Contacts...

Double icon illuminated pushbuttons • bushing Ø 24 or 26 mm • momentary or latching BUILD YOUR PART NUMBER BASIC PART NUMBER ELECTRICAL FUNCTIONS Round, flat Solder lugs LED linked to actuator, green if switch in ON position, single pole LED linked to actuator, red if switch in ON position, single pole Silver, gold plated ACTUATOR COLOR Smoke black BEZEL COLOR START (green) / STOP (red) with ring ON (green) / OFF (red) with ring I (green) / O (red) with ring ABOUT THIS SERIES On the following pages, you will find successively basic part numbers of switches and options in the same order as in...

MOUNTING BY THREADED BUSHING Ø 24 (.944) Double icon illuminated pushbuttons • bushing Ø 24 or 26 mm • momentary or latching PANEL SWITCHES LED CONTROL AND NUMBER OF POLES To order a product, replace • with one of the following codes, then add the desired options. Function 1 (latching) CFDSHC1 CFDSHC1 Independent LED single pole C Independent LED double pole D CFDSHC1 CFDSHC1 Red LED in ON position single pole G CFDSHD3 CFDSHG1 green line = jumper LED- has to be wired to one CFDSHD3 to be wired by the user. pin of pole 2. Green LED in ON position single pole F -

Double icon illuminated pushbuttons • bushing Ø 24 or 26 mm • momentary or latching CONTACT MATERIALS BASIC P/N Silver Silver, gold plated ACTUATOR COLOR BASIC P/N Smoke black BEZEL COLOR BASIC P/N Black LED COLOR BASIC P/N Red/green LED RESISTOR BASIC P/N No resistor supplied 12 VDC resistor 24 VDC resistor 30 VDC resistor 15 VDC resistor SYMBOLS BASIC P/N START (green) / STOP (red) with ring ON (green) / OFF ( red) with ring I (green) / O ( red) with ring FLAT PANEL SWITCHES