MONITOR DELTA 80 WITH INTEGRATED GPS NAVIGATOR
9Pages

MONITOR DELTA 80 WITH INTEGRATED GPS NAVIGATOR

LEGENDA SIMBOLI LEGEND OF SYMBOLS = Generic danger = remote control unit IBX100 This manual is an integral part of the equipment to which it refers and must accompany the equipment in case of sale or change of ownership. Keep it for any future reference; ARAG reserves the right to modify product specifications and instructions at any moment and without notice

RISKS AND PROTECTIONS BEFORE ASSEMBLY All installation works must be done with battery disconnected, using suitable tools and any individual protection equipment deemed necessary. Use ONLY clean water for treatment tests and simulations: using chemicals during simulated treatment runs can seriously injure persons in the vicinity. INTENDED USE Delta 80 features a satellite navigator that – through the external GPS receiver – can be used for agricultural applications and navigation. The device you have purchased is a monitor which, when connected to an adequate remote control unit (ECU),...

POSITION ON FARMING MACHINE Monitor positioning • The Delta 80 monitor must be placed in the control cabin of the farming machine. Observe the following precautions - Do NOT install the monitor in areas where it would be subjected to excessive vibrations or shocks, to prevent any damage or accidental use of the control keys; - Install the device in a visible position within easy reach by hand; bear in mind that the monitor should not obstruct the operator’s freedom of movement or block his view. Consider all necessary connections of the monitor (Fig. 2), the cable length, and make sure...

WIRING CONNECTIONS • Only use ARAG harnesses suitable for Delta 80 monitor. • Take care not to break, pull, tear or cut the cables. • Use of unsuitable cables not provided by ARAG automatically voids the warranty. • ARAG is not liable for damages to the equipment, persons or animals caused by failure to observe the above instructions. Auxiliary function and power supply connection WARNING: To avoid short circuits, do not connect the power cables to battery before the installation is completed. Before powering up the monitor, make sure the tractor battery voltage is as specified (12 VDC)....

Modem 3G • Insertion Insert the SIM card making sure to orient it correctly: the card cut edge D must be face up; push the card until it engages into place and close the slot with the cover MAKING SURE IT IS DULY CLOSED TO AVOID WATER SEEPAGE. • Removal To remove the SIM card, press and immediately release the card into the slot and slide it out. Insert / remove with DEVICE OFF. Pendrive The pen drive may be used to exchange data with the Delta 80 monitor. Before use, format the SD board in FAT 32 mode; make sure that the board is not protected and can be read by the system. Compatible with...

MAINTENANCE / DIAGNOSTICS / REPAIRS 8 MAINTENANCE / DIAGNOSTICS / REPAIRS Troubleshooting FAULT The display does not switch on • Check power supply connection Cleaning rules - Clean only with a soft wet cloth. - DO NOT use aggressive detergents or products. - DO NOT aim direct water jets. TECHNICAL DATA DESCRIPTION Display Rated supply voltage Consumption Operating temperature Storage temperature Weight (without cables) Driving direction input (REVERSE IN) DELTA 80 LCD 8,4", 65000 colors, 500 cd/m2 12 Vdc (9 ÷ 16 Vdc) monitor: 1,5 A 0 °C ÷ 45 °C +32 °F ÷ +113 °F -20 °C ÷ 60 °C -4 °F ÷ +140...

END-OF-LIFE DISPOSAL This device contains a lithium polymer battery that, at end of life, must be disposed of according to the prevailing rules. Should it be necessary to replace the battery, do not disassemble the device but contact ARAG directly. The device must be used and stored at the temperature indicated in chapter "Technical data" of this manual. Excessive temperature oscillations may cause acid leakage, overheating, explosion or self-combustion of the battery and consequent injuries and/or damages to persons. Do not open, remove, drill or throw the device in the fire. In case of...

Only use genuine ARAG accessories or spare parts to make sure manufacturer guaranteed safety conditions are maintained in time. Always refer to the internet address www.aragnet.com 42048 RUBIERA (Reggio Emilia) - ITALY Via Palladio, 5/A Tel. +39 0522 622011 Fax +39 0522 628944 http://www.aragnet.com info@aragnet.com