BL 120
12Pages

BI^ASSIspa OPERATION AND MAINTENANCE MANUAL POWER HOE SERIES BL 120

0 INTRODUCTION 0 SAFETY REGULATIONS 0 IDENTIFICATION DATA 0 EC MARKING 0 TECHNICAL SPECIFICATIONS 0 SAFETY DEVICE 0 TRANSFER PRINTINGS - INSTRUCTIONS SAFETY 0 MOTOR-HOE CONTROLS 0 OPERATING THE CONTROLS 0 INSTALLATION 0 OPERATING THE MOTOR-HOE 0 MAINTENANCE 0 CHECK AND ADJUSTMENTS AND 0 EC CERTIFICATE OF CONFORMITY INTRODUCTION • This manual provides Use and Maintenance instructions, technical specifications, and safety precautions for motor-hoes model BL 120. Read this USE and MAINTENANCE Manual carefully before using your new motor-hoe. This manual provides the most up-to-date information...

DECALS Read all the decals attached to the motor-hoe and follow their prescriptions before starting, driving, refuelling or servicing the machine. Replace immediately any damaged or illegible decals. SUITABLE CLOTHING Do not wear wide and flapping clothes that could be caught in moving parts. Always wear robust gloves when servicing the motor-hoe or coupling attachments. Do not operate your motor-hoe barefoot, wearing sandals or shorts. Wear heavy shoes and trousers. PHYSICAL CONDITION Do not drive the motor-hoe if your physical condition is not suitable. NOISE In order to reduce the...

BL 120 Use your motor-hoe only in daylight or with good artificial lighting. Operate it at walking pace. Do not run. Take particular care on slopes; operate only under safe and stable conditions. Do not work uphill or downhill; move across the slope instead. Take special care when turning. Do not operate on slopes over 30°. Do not use your motor-hoe without its protection guards. Do not operate the motor-hoe if protection guards or other safety devices are missing or defective. Keep your hands and feet clear of all attachments. Do not lift or transport your motor-hoe with the engine...

BL 120 TECHNICAL SPECIFICATIONS FOR THE ENGINE FEATURES, SEE THE ENGINE INSTRUCTION BOOKLET DELIVERED WITH THE MACHINE. STARTING Auto-winder device. CLUTCH Twin plate dry clutch with control lever on left handlebar. GEAR Three forward speeds and one reverse speed (with safety device). Speed are engaged through a control lever fitted to the column. The maximum speed that can be attained, according to type of tire (on request) fitted on the machine. TRANSMISSION Oil bath gear box with bevel gear pairs to drive tiller rotor. POWER TAKE OFFS (PTO) Two power take offs: - Upper power take off is...

BL 120 SAFETYDEVICE The motor-hoe is fitted with the following safety device to ensure maximum safety in machine operation: - Reverse speed engagement control lever which, when released, disengages reverse speed automatically. A Do not interfere with the safety device. Do not use the motor-hoe if the safety device is missing or defective. TRANSFER PRINTINGS - INSTRUCTIONS AND SAFETY Please find below the adhesive transfer printings shown on the machine. For accident prevention purposes, they must always be clearly readable. Should they be damaged, it is compulsory to replace them by...

BL 120 MOTOR-HOE CONTROLS See figure 5. 1. Throttle control lever. 2. Reverse speed engagement control lever (accident prevention device). 4. Handlebar lock release lever. 5. Engine stop lever. OPERATING THE CONTROLS Refer to figure 5. Throttle control lever (1) - Lever (1) in up position: engine at idle. - Lever (1) in down position: maximum engine rpm. Reverse speed engagement control lever (2) Reverse speed engagement control lever (2) is an accident prevention device. Do not use the motor-hoe if this safety device is defective. The lever is operated as follows: a. Set the throttle...

BL 120 INSTALLATION INSTALLATION OF ROTARY TILLERS The tool shaft has hexagonal cross-section to allow quick and easy installation of rotary tillers or other attachments. Proceed as follows (see figure 6): a. Clean the rotary tiller hubs (1) and hexagonal shaft (2) thoroughly applying a little grease to facilitate assembly and future removal. b. Fit the rotary tiller hub onto hexagonal shaft and secure it by means of the pin provided c. Bear in mind the following: - The cutting edge of tiller rotors must face toward the motor-hoe front part. - For tilling on sandy or stone-free ground, fit...

BL 120 OPERA TING THE MOTOR-HOE STARTING THE ENGINE NOTE See the engine Operation and Maintenance Manual for all informations regarding the engine. CAUTION Oil bath air filter (if fitted) - When delivered new, there is no oil in the air filter. Before using your motor-hoe, add motor oil up to the marked level. a. Disengage all control levers before starting the engine. b. Open the fuel cock (if present). c. If cold starting the engine, use the choke fitted on the carburator (gasoline engine only). d. Press down the engine stop lever (figure 10, item 1) and, at the same time, pull clutch...

OIL BATH AIR FILTER Every 8 hours Check the oil level in the air filter. If necessary, top up with engine oil. Clean the filter element as instructed in the engine Operation and Maintenance Manual. NOTE Filter cleaning frequency depends on operating conditions, but should never be more than 8 hours GEARBOX AND TRANSMISSION After the first 50 hours (running in) Change the gear/transmission oil (see figure 12). Change the oil when the engine is hot to facilitate draining of exhausted oil. a. Remove the oil filler breather plug (1). b. Remove the oil drain plug (2) from the bottom of the...

SAFETY TESTS AND CERTIFICATION Declaration of CE conformity in accordance with EEC directive 89/392 and amendments. 40010 San Matteo della Decima BO Italy Via Lampedusa 1 Tel. (051) 682.46.56 Declare on their own responsibility, that the machine POWER HOE TYPE Conforms to the basic Safety and Health Requirements as stated in EEC 89/392 Directives, and succesive modifications In order to verify the correct application of the aforementioned Directives, the following Conforming Standards were consulted pr EN 709 CHAIRMAN OF THE BOARD S. Matteo della Decima 20/10/97