FC 210 3VS
8Pages

OPERATION AND MAINTENANCE MANUAL SICKLE BAR MOWER SERIES

FC 200 3VS CONTENTS STARTING AND STOPPING THE MACHINE OPERATING AND REGULATING THE MACHINE MAINTENANCE ACCESSORI WARRANTY SAFETY TESTS AND CERTIFICATION INTRODUCTION ♦ Thank you for having selected our product. We would like to welcome you among our many customers. ♦ We are certain that you will appreciate the performance and the operating ease of this machine. ♦ Our wide experience in the sector, the use of top grade materials and the high quality production ensure the flawless efficiency of the machine, which is designed to give many years of use if operated and maintained correctly. ♦ We...

IDENTIFICATION AND TECHNICAL CHARACTERISTICS FOR THE ENGINE FEATURES SEE THE ENGINE INSTRUCTION BOOKLET DELIVERED WITH THE MACHINE. • All the engines which can be fitted on this machine have the recoil starter and protection on the exhaust. • Fuel for 4-stroke engine : Unleaded petrol • Fuel for Diesel engine: Diesel oil • Safety device on handles to stop machine • Air filter in oil bath • Consumption at 3600 r.p.m.: 0.8 Kg/hour • ENGINE LUBRICATION: SAE 30 OIL • Oil quantity in motor: 0.6 lt. • Transmission : 2 forward gears + Reverse gear • TRANSMISSION LUBRICATION : SAE 80W/90 OIL • Oil...

FC 200 3VS PACKING AND TRANSPORT 0 WIDTH: 116 cm 0 DEPTH: 42 cm 0 HEIGHT: 63 cm ^ Remove the power mower from its packing. ^ Secure the handles with the screw (Pict. 10 Ref. “A”). The handle support is secured on anti-vibration devices (see Pict. 4 Ref. “B”). ^ Fit the cutter bar into the machine by the quick coupling (see Pict. 6) ^ If the machine is to be transported, empty out the petrol tank and always apply the plastic protective strip to the E.S.M. cutting bar blade. Read the E.S.M. sheet attache. IMPORTANT: THE PACKED MACHINE IS SUPPLIED WITH THE MOTOR WITHOUT OIL OR PETROL. SAFETY...

Every time you get ready to start the motor, make a careful check of the following: • Make sure that fuel is in the tank. • Check engine oil level. IMPORTANT: ENGINES OF NEWLY MANUFACTURED MACHINES DO NOT CONTAIN OIL. In this case, fill with oil up to the oil plug stick. • CONSULT THE OPERATION AND MAINTENANCE MANUAL OF THE MOTOR UNDER "BEFORE START-UP" • Make sure oil is up to the level in the gearbox (Pict. 12 Ref. B) • Check that all safety systems are released and functioning. • Before starting the machine, when the engine is cold, pull the choke, if it is fitted on your machine. •...

BENASSI s.p.A.OPERATING AND REGULATING THE MACHINE- Piet. N.10 - Before you start mowing, oil the cutting blade, then start the motor as follows: The release of the wheels and bar clutches should be done with the engine running at low speed. Engaging the transmission to the wheels and the cutting bar by means of the clutch lever must be carried out with the motor at a middle r.p.m. and by slowly releasing the lever. When starting to mow, position the accelerator lever at 3/4 or at "MAX" to ensure adequate power. When mowing along a wall or the edge of a sidewalk, be careful to keep a safety...

ACCESSORIES > PAIR OF RUBBER WHEELS 4.00.8 > PAIR OF RUBBER WHEELS 16/650.8 (with 50 mm spacers) > PAIR OF IRON WHEELS > PAIR OF “DAISY” TYPE IRON WHEELS (applies to 4.00.8 wheels only) > PAIR OF 50 mm SPACERS FOR WHEELS > PAIR OF 112 mm SPACERS FOR WHEELS > PAIR OF HUBS FOR TWIN-WHEELS > PAIR OF SIDE WINDROWING ATTACHMENTS FOR SEMI-DENSE MOWING UNIT > PAIR OF EXTENSIONS FOR WINDROWING ATTACHMENTS > SNOW PLOUGH 50 x 45 cm > LARGE BRUSH 100 cm > FRONT SNOW-PLOYGH BLADE TYPE OF BAR : ESM BAR 117 cm SPECIAL BAR 107 cm SEMI-DENSE BAR 112 cm WARRANTY The machines and accessories are guaranteed...

FC 200 3VS SAFETY TESTS AND CERTIFICATION BENASSI Declaration of CE conformity in accordance with the directive 98/37 CE and the directive EMC 89/336/CE S.p.A. Via Lampedusa n°1 - 40017 San Matteo della Decima BO Italy We hereby declare that the machine complies with the essential requirements for health and safety in accordance with Directive 98/37/CE. TYPE: POWER MOWER SERIES: FC 200 3VS MODEL: FC 210 KD 3VS / FC 210 H 3VS For verification of the conformity with the above-mentioned Directives reference has been made to following specifications: UNI EN ISO 12100-1 and UNI EN ISO...