◊ INTRODUCTION ◊ EXPLANATION OF THE MACHINE ◊ TECHNICAL SPECIFICATIONS ◊ PACKING AND ASSEMBLING THE MACHINE ◊ SAFETY RULES AND LIMITS ◊ TRANSPORT ◊ STARTING AND STOPPING ◊ WORKING AND ADJUSTMENTS ◊ MAINTENANCE ◊ GUARANTEE ◊ SAFETY TESTS AND CERTIFICATION ♦ Thanking you for preferring our product, You are welcome among our many confident customers. ♦ We are sure that the performances and the simplicity of use of this machine will give you any satisfaction. ♦ This machine is carefully built with high quality components, and if it will be properly maintained, it will last for long time, giving you...

EXPLANATION OF THE MACHINE: 1) Motor Stop 9) Side Discharge Guard. 11) Mowing Height Adjustment. 12) Drive control Lever. 14) Wheels Shaft with Pin. 7) Primer (only Briggs & Stratton engine) 15) Gasoline Tap ( only Honda engine). 16) 3 Speeds Gear Lever (FT 533 )

For the engine features see the engine instruction booklet delivered with the machine. • Fuel : unleaded petrol • Recoil Starter. • Dry Air filter . • Oil in the gearbox : AGIP Diesel SIGMA SAE 30 0,6 Lts. • Max. Speed of the machine : (FT530) Speed 3 km/hour • (FT533) : 1° speed:2,5 km/h; 2° Speed :3,2s km/hr; 3° Speed: 4,0 km/hr • Safety electric stop on the andle-bar. • Guidance handlebars can be adjusted in many positions (vertical and side adjustment) The identification details of the machine ( Code Number, Engine Number, Weight, Power), are listed in a little Number Plate, as shown in Pict....

WARNING! When the Drive Lever,Pos..A Pict. 5 is completely pressed, the 2 little levers of the transmission Rif."A and" B" Pict.12 should keep a margin of 2 mms. Extra. You can adjust the cable on this position working on the screw, Pos."F" Pict. 5. • The adjustment of the mowing height , through lever B, in Pict. 5, should be done with engine OFF. This lever is blocking the whole chassis in three different positions. You can adjust this cable, through the screw Pos. E in Pict. 5. • The cable of the accelerator doesn't need any adjustment. • Through the gear-lever ( Pos." H" in Pict.5), you can...

THE OPERATOR MUST ALWAYS WEAR NOISE-PROTECTIONS FOR THE HEARS. • Read carefully this User’s manual, before using the machine. • It is strictly forbidden using the machine to boys under 16 years. • The operator is responsible of the damages caused to other people. • When the machine must be transported on a vehicle, the fuel tank should be absolutely EMPTY. • Before leaving the machine, make sure that it could not accidentally start. • Don't work without wearing strong shoes, and long trousers. • Please inspect the area where you are going to work, and remove any branches, stones and other obstacles which...

TRANSPORT • It is very easy pushing the machine - the free wheels transmission and the front support-wheel give a very smooth move. • For an easier transport in car boot, you can turn off the handle-bars, after releasing the blocking screw-lever ( see Pos. A in Pict.3). STARTING, RUNNING AND STOPPING THE MACHINE Before starting the engine, you must do the following operations: • Check the fuel level in the tank, opening the fuel cap. • Check the oil level in the engine. IMPORTANT ! The New machine is delivered without oil. • READ CAREFULLY THE BOOK “USE AND MAINTENANCE OF THE ENGINE” • Push the"...

S.p.A. FREE WHEEL BLOCKING • • • • The wheels are blocked through two rings at both ends of the transmission shaft. One of these rings is provided with a pivot and can be fixed in two different positions: Pivot position towards the outside (picture D): in this position the wheel is free to turn, this produces a differential effect and helps the machine while moving forward in a curve. Pivot position towards the inside (picture A): in this position the wheel is blocked to the shaft so that the differential effect is lost. In this way, however, if the machine moves on a downhill ground it follows...

• Working in extreme conditions, with very high and strong grass, it could happen that the blade is blocked by the grass. In this case, you can increase the mowing height, and reduce the working width of each passage. • If you need a “ Mulching” effect, you should leave the mowing deck closed, with the protection guards mounted. • When you are driving the machine near a wall or a stoned path, be very careful, because it could damage the blade. • For moving the machine Forward and Backward with the engine OFF, please don’t push the clutch lever ( Pos. A in Pict.5). • The front little wheel is...

Also the front wheel should be greased, through the greasing hole, ( Pos. C in Pict.9). Lubricate with grease the wheel-hubs , after removing the wheels from the shaft, unscrewing the screw (Pos. 14 in Pict.1),and leave some grease on the bearings. • All the control cables should be lubricated, adding grease into the sheathing. • Carefully cleaning all the machine, removing dust and mowing rests from the internal deck. Don’t use high pressure cleaning machines, better a brush or an air compressor. WARRANTY The machines and accessories are guaranteed for 2 years, with the exception of electrical...

- Via Lampedusa 1 - 40010 San Matteo della Decima BO Italy We hereby declare that the machine conforms with the essential requirements for health and safety in accordance with EEC Directive 89/392 and amendments. HIGH GRASS ROTARY MOWER TYPE The machine is accomplying the Standard2000/14/CE, confirmed by the regulation N° 262 dated Sept.4th, 2002. Type of Machine : LawnMower, according to the specification n.32, of the attached 1 Dir. 2000/14/CE. Procedure applied for checking the conformity : Attached VI, Dir. 2000/14/CE, Procedure2. Checking Institute n. 0714: ECO S.p.A. Via Granarolo,62 48018...