OPERATOR'S MANUAL DISC HARROW

TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that all Dealer Check List items have been completed. Dealers can register all Woods product at dealer.WoodsEquipment.com under Product Registration. Failure to register the product does not...

TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 OPERATION . . . . . . . . . . . . . . . . . . . . . . . ....

Working Width Blade Type Notched or Combo Notched or Combo Notched or Combo Blade Diameter Blade Spacing Axle Size Bearing Type Sealed, Self-Aligning Sealed, Self-Aligning Sealed, Self-Aligning Sealed, Self-Aligning, Sealed, Self-Aligning, Greaseable Greaseable Bearing Hangers 1/4" Plate, U-Bolt Frame Construction 3" x 3" Tube and Angle Disc Gang Tube Mud Scrapers Furrow Fillers Mud Scrapers Furrow Fillers Mud Scrapers Furrow Fillers Rear Drawbar Mud Scrapers Furrow Fillers Rear Drawbar GENERAL INFORMATION The purpose of this manual is to assist you in operating and maintaining your Disc Harrow....

SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment. It has been said, “The best safety device is an informed, careful operator.” We ask you to be...

SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page)  Look down and to the rear and make sure area is clear before operating in reverse.  Use extreme care when working close to fences, ditches, other obstructions, or on hillsides. when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death.  Do not operate or transport equipment while under the influence of alcohol or drugs....

SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 1 - SERIAL NUMBER PLATE Use a clean, damp cloth to clean safety decals. Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off. Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 4 - PN 1006885 5 - REAR RED REFLECTOR (PN 20106) Located on rear of frame (DHS64) (Not Shown). 6 - REAR RED REFLECTOR (PN 57123) Located on rear of rear gang tubes (DHS80, DHM80, DHM96) (Not Shown). 7 - FRONT AMBER REFLECTOR (PN 1002940) Located on front of all gang tubes (DHM96) (Not Shown). 8 - SAFETY DECAL SET (PN 1042082) Includes decals 2 - 5 (DHS48, DHS64). 9 - SAFETY DECAL SET (PN 1042085) Includes decals 2 - 4, 6, 7 (DHS80, DHM80, DHM96).

OPERATION The operator is responsible for the safe operation of this equipment. The operator must be properly trained. Operators should be familiar with the equipment, the tractor, and all safety practices before starting operation. Read the safety rules and safety decals, page 5 through page 8. The Disc Harrow is designed for a wide range of applications: leveling, grading, and discing. Recommended tractor ground speed for most conditions is from 2 to 6 mph. CAUTION  Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, set parking brake, remove key, inspect,...

DHS48 - Category 1 (See Figure 1) 1. Place tractor 3-point lower lift arms over outer hitch pins (1). 2. Secure with klik pins (2). 3. Attach the tractor’s top link to the top hole of the Disc Harrow frame (3). 4. Secure with the heavy-duty top link pin and retaining pin supplied with the tractor top link. DHS48 - Category 0 (Optional) (See Figure 3) 1. Place tractor 3-point lower lift arms over inner hitch pins (1). 2. Secure with safety pins. (Not provided) 3. Attach the tractor’s top link to the top hole of the Disc Harrow frame (4). 4. Secure with the heavy-duty top link pin and retaining...

DHM80, 96 - Category 1 (See Figure 6) 1. Place tractor 3-point lower lift arms between inner mounting lugs. 2. Secure with Category 1 hitch pins (1) and klik pins (2). 3. Attach the tractor’s top link to the middle hole of the Disc Harrow frame (3). 4. Secure with the heavy-duty top link pin and retaining pin supplied with the tractor top link. DHS64, 80 - Quick Hitch (Optional) (CAT 1 Only) (See Figure 5) The DHS64 & 80 Disc Harrows will attach to a Category 1 quick hitch. 1. Use Quick Hitch Bushing Kit 1022043 when using a quick hitch coupler. 2. Remove lower hitch pins (1) from Disc Harrow...