L2-Trail + M-Trail
16Pages

Operator's Manual

Colour codes

Safety Safety and protection ●● Read Operator’s Manual and safety rules before starting. ●● Read Operator’s Manual for the PTO shaft. ●● Do not leave the tractor cabin without stopping the PTO system of the tractor! ●● Turn off tractor engine and all electrical controlling devices during maintenance and other intervention on the spreader ●● Ensure that bystanders maintain a sufficient safety distance from the spreader as long as the tractor engine is on. ●● Do not enter the spreader when the tractor engine is on. ●● Do not wear loosely fitting clothes that could become entangled with moving...

Safety Legend Read Operator’s Manual and safety rules before starting. Never go under a raised spreader. Never go between spreader and tractor when engine is started. Never use the ladder when the spreader is not mounted on a tractor. Safety distance for flying material must be observed. Never go behind the spreader with rotating spreading discs. Avoid contact with rotating parts. Never put hand/object into the hopper with rotating spreading discs. Avoid contact as long as parts are moving. Never clean the spreader with rotating spreading discs. Do not spray water in this area. Noise level...

Liability Liability You are fully responsible for the setting of the spreader. The spreader must be set according to the fertiliser in use. Be aware that the fertiliser batch tested in the BOGBALLE A/S test facilities may differ from the fertiliser delivered to you even if with the same specifications. BOGBALLE A/S cannot be held responsible for any kind of personal injury, crop damage, after effects etc.

Main settings Main settings If the spreader is mounted on M-Trail or other carriages – the distance from the ground to the spreading discs is increased from 75 cm, typically up to 100 cm to 140 cm. Spread width H: 100 - 140 cm. (see figure 1) Tilt angle- reduction (according to Spread chart) Example Height Spread width Spread chart Tilt angle M-Trail

Setting and Service M45-Trail - height adjustable implement carrier The system makes it possible to optimise the spreader height in proportion to the M45-Trail (see figure 1). In cases where the spreader must be tilted negative (-) the spreading vanes can collide with respectively the guards and the wheels. If this is the case the lifting system must be raised to a minimum distance of 10 cm between guards / wheels. M45-Trail - tightening of construction The 2 + 2 pcs. of M30 bolts MUST be tightened at 1200 Nm (see figure 1). It is recommended to tighten up the construction after 2-3 working...

Setting and Service L2 / M35-Trail and M45-Trail - PTO Tractor ●● A standard PTO shaft can maximum resist an angle turning of 25º ●● A wide angle PTO shaft can maximum resist an angle turning of 80º If there is a need for turning angles higher than 25º - The carriage must be fitted with a wide angle PTO shaft. L2 / M35-Trail and M45-Trail - adjustment of wheel hub Servicing and adjusting the clearance in the taper roller bearings on the wheel hub. It is important to check and adjust the clearance every 50 hours of use. After every 50 hours: ●● Position the Trailer on a level and stable...

Remember always to grease the entire spreader in a corrosion protective oil. It is not sufficient just to wash the spreader, as dried-in fertiliser dust will absorb water and escalate corrosion. Mineral fertiliser is extremely corrosive and often with a high content of nitrogen and sulphur, which combined with water generate sulphuric acid. Remember to: • Cover/oil the spreader carefully before using it the first time. • Oil seals up joints and connections between components – to prevent fertiliser dust from getting in and building up between the various spreader parts. • Wash and...

Manufacturer: BOGBALLE A/S Bogballe DK-7171 Uldum Phone +45 7589 3266 Fax +45 7589 3766 Declares that machine: Under carriage for Centrifugal fertiliser spreader: L2-Trail / M35-Trail / M45-Trail Is made in conformity with: Directive of 17th May 2006 conc. mutual approximation of the laws of the member states on machines (2006/42/ EØF), with special reference to the enclosure II, A and enclosure I of the directive, conc. essential safety and health claims in connection with construction and manufacture of machines. International/national standards: DS/EN ISO 12100 DS/EN ISO 13857 1st...

FIND MORE INFORMATION ON www.bogballe.com