10" & 13" Backsaver Augers
32Pages

ASSEMBLY INSTRUCTION MANUAL 10" & 13" Backsaver Augers Electric Mover Kit

Farm King _ Table of Contents - 10" and 13" Backsaver Augers - Electric Mover Kit Manufacturer's statement: for technical reasons Buhler Industries Inc. reserves the right to modify machinery design and specifications provided herein without any preliminary notice. Information provided herein is of descriptive nature. Performance quality may depend on soil fertility, applied agricultural techniques, weather conditions and other factors.

Introduction - 10" and 13" Backsaver Augers - Electric Mover Kit Introduction The new line of electric power movers from Farm King allows remote positioning of the swing auger hopper. The system is 100% electric and with no hydraulic flow required the hoppers can be positioned for use without the need to start and idle the tractor first. The remote boasts a range of 300+ feet, and can operate in extreme weather, heat and cold. The mover’s drive motors mount to the hopper body itself, putting the weight of the self-leveling hopper on the tires for excellent traction. Each drive motor is...

Safety - 10" and 13" Backsaver Augers - Electric Mover Kit Safety Safety Instructions Remember, YOU are the key to safety. Good safety practices not only protect you, but also the people around you. Make these practices a working part of your safety program. Be certain that everyone operating this equipment is familiar with the recommended operating and maintenance procedures and follows all the safety precautions. Most accidents can be prevented. Do not risk injury or death by ignoring good safety practices. The alert symbol is used throughout this manual. It indicates attention is...

Safety - 10" and 13" Backsaver Augers - Electric Mover Kit Farm King _ General Safety Instructions • Have a first-aid kit available for use and know how to use it. • Have a fire extinguisher available, stored in a highly visible location, and know how to use it. • Wear appropriate protective gear. This list may include but is not limited to: - hard hat - protective shoes with slip resistant soles - protective glasses or goggles - heavy gloves - wet weather gear - hearing protection - respirator or filter mask • Read and understand the Operator's Manual and all safety signs before operating,...

Safety - 10" and 13" Backsaver Augers - Electric Mover Kit Farm King Transport Safety • Review Transport Safety instructions in tractor manual before moving. • Check with local authorities regarding transport on public roads. Obey all applicable laws and regulations. • Do not tow equipment that does not have brakes at speeds over 20 mph (32 km/h). • Do not tow equipment that does not have brakes that, when fully loaded, has a mass (weight) over 3,300 lb (1,497 kg) and more than 1.5 times the mass (weight) of the towing unit. • Make sure the SMV (Slow Moving Vehicle) emblem and all the...

Safety - 10" and 13" Backsaver Augers - Electric Mover Kit Safety Signs • Keep all safety signs clean and legible and replace any that are damaged or missing. • When original parts are replaced, any safety signs affixed to those parts should be replaced as well. Replacement safety signs are available from your local dealer. Installation • To install safety signs, ensure area is clean and dry. Decide on the exact position before you remove the backing paper. Remove the smallest portion of the split backing paper and align over the specified area. Carefully press in place. • Slowly peel back...

Farm King Assembly - 10" and 13" Backsaver Augers - Electric Mover Kit Farm King Assembly - 10" and 13" Backsaver Augers - Electric Mover Kit Assembly 10" & 13" Electric Motor Mounts The electric motor mounts for the 10" & 13" hopper are universal. To install each motor, place the flat back of the mount against the front face of the hopper. The mount has three hole combinations to choose the height of the hopper. Place a 3/8 x 1" (10 x 25 mm) bolt through holes 1 and 3. Place the 3/8" (10 mm) lock nut on the backside of these bolts and tighten. Place a 3/8" x 1" (10 x 25 mm) bolt through...

Farm King Assembly - 10" and 13" Backsaver Augers - Electric Mover Kit The image on the right shows how the setup should look when complete. Repeat this process for the other side. Farm King Assembly - 10" and 13" Backsaver Augers - Electric Mover Kit

Farm King Assembly - 10" and 13" Backsaver Augers - Electric Mover Kit The electric motor mounts for the 10" TM hopper are not universal and will only fit on one side of the hopper. The hookups for the lift cable and safety chain will be on the top of the mounts when installed properly. Mount the motors onto the hopper by sliding the solid pin and bolt into the holes on the corner of the hopper so that the motor is to the side of the hopper. Then insert a 3/4" x 4-1/2" (19 x 114 mm) bolt through the hole on the front of the mount that lines up with the remaining hole on the hopper. This...

Farm King Assembly - 10" and 13" Backsaver Augers - Electric Mover Kit Farm King Assembly - 10" and 13" Backsaver Augers - Electric Mover Kit 10" Feterl Original Electric Swing Drive Mount the proximity sensor onto the drive section. The proximity sensor mount replaces the large galvanized washer that holds the swivel plate. The proximity sensor should be mounted on the stud that is towards the main auger tube with the swing spout passing over from above, as shown in the image below. *Note: If moving the hopper from one side of the auger to the other, the proximity sensor needs to be...

Farm King Assembly - 10" and 13" Backsaver Augers - Electric Mover Kit Feed the power and proximity sensor cables through the top loop and over the top of the discharge head. Place a P-clamp on both cables where the cables pass by the gear box. Secure the P-clamps to the gearbox by screwing a 3/8" x 3/4" (10 x 19 mm) bolt with 3/8" (10 mm) lock washer into one of the threaded holes on the side of the gearbox, as shown in the image below. Remove the slack from the proximity sensor cable between the control box and the P-clamp and connect the proximity sensor cable to the proximity...