OUTRIGGER FOR COMPACT CARRIER VEHICLES

Outrigger KBM 350 The KBM 350 outrigger is supplied as a combined rear and front attachment for small tractors from 19 KW (25 HP) upwards. A conversion from front to rear attachment as well as left-hand to right-hand work is possible. It is easily attached to the three-point hydraulics cat. I + II. The drive of the working equipment is hydraulic. The integrated hydraulic system is driven via the tractor‘s PTO shaft. The outrigger arms are operated via the supplied electro-hydraulic control unit. Due to the compact design, there is no line-of-sight obstruction even as front attachment during transport...

Outrigger UNA 100 and UNA 200 The UNA 100 and UNA 200 uni arms are specially designed as attachments on multi-purpose municipal vehicles with their own hydraulic system and hydraulically height-adjustable front attachment plate. The basic devices are used to hold various working equipment. The working equipment can be used on the left, right and in front the vehicle by means of a hydraulic drive. Thanks to the symmetrical design of the basic devices and the individual working equipment, the outrigger may be located on the right or alternatively the left. To absorb the momentum of the outrigger...

Outrigger DBM 400 The Dücker outrigger DBM 400 can be used universally with a range of up to 4.45 metres, a low transport width and a large number of work implements. The DBM 400 has specifically been designed for front attachment to municipal carrier vehicles or tractors and can be held by the three-point linkage in sizes cat. I. + II. or via an attachment plate. With its special kinematics, the Dücker outrigger DBM 400 permits flexible and easy use in nearly any working position. Conversion of the working position from right-hand work to left-hand work is possible easily and quickly. • Working...

Outrigger DBM 400 with DÜCKER-Tasttronic DBM 400, integrated hydraulic system The DÜCKER-Tasttronic is available as an option on the outrigger DBM 400. The microprocessor-controlled control developed by DÜCKER provides all functions of the proportional single-lever control. In addition, the fully encapsulated signal recording integrated in the mowing head allows for automatic and very precise level adjustment. This allows for safe work at high driving speeds. The Tasttronic does not comprise any movable, dirt and dust sensitive actuators. The signal recordong is performed by means of flexion...

Working Equipment HSL 15 Cuttersystem Working width: 1500 mm Cutting thickness: until 30 mm Weight: approx. 85 kg HS 16 Hegde-Cutter Working width: 1600 mm Cutting thickness: until 45 mm Weight: approx. 120 kg HS 130 HR Hegde-Cutter Working width: 1300 mm Cutting thickness: bis 25 mm Weight: approx. 165 kg TMK 10 Flail-Mower-Head Working width: 1000 mm Revolutions of shaft: 2200 rpm Weight: 180 kg MKL 10 Flail-Mower-Head Working width: 1000 mm Revolutions of shaft: 2700 rpm Weight: 180kg PFP 600 Pavement Cleaner Working width: 600 mm Revolutions of shaft: 150 rpm Weight: 140 kg LPW 500 Reflector...

Counterweights and attachment plate Attachment plate size F2 Counterweights for three-point or attachment fittings Range diagrams Transport width Weight basic device Swivel angle of equipment Right- and left-hand work Drive for working equipment 60 ltr. / 200 bar Control Attachment Front or rear PTO shaft Power hydraulics from the vehicle or front PTO shaft Electro-hydraulic control Electro-hydraulic control or from the vehicle Front or rear attachment Three-point cat. I + II Front attachment plate or three-point hitch cat. I + II Technical data

Gerhard Dücker GmbH & Co. KG 48703 Stadtlohn, Wendfeld 9, Germany Telefon 0 25 63 / 93 92 - 0 Telefax 0 25 63 / 93 92 90 E-Mail [email protected] Internet www.duecker.de 04/2020 - Oing-Druck - Rights reserved for changes and further developements. Technology for environmental landscape maintenance a