V1.4 DTD Automatic Controller Manual

Product catalog summary

Introduction
This document is a manual for the V1.4 DTD Automatic Controller used in poultry broiler operations. It provides detailed instructions on setting up and operating the controller to manage lighting conditions effectively.

Main Features

Main Power On Indicator
Ramp Up and Ramp Down Indicators
2 Channel Basic Mode with Twin Ramp Up and Ramp Down Operations

Setting the Clock

Access the Set Clock screen from the Home screen using the down cursor.
Select the Day Set screen and adjust the day using the Up/Down cursors, then press Enter.
Set the current hour and minutes similarly, confirming each with Enter.
The unit returns to the Home screen after 30 seconds of inactivity or by pressing Restart.

Channel Selection

Navigate to the Select Channel screen from the Home screen.
Choose either Channel A or B using the Up/Down cursors and confirm with Enter.
Ensure the correct channel is set when adjusting light settings.

Setting the Function

Access the Set Fade Time screen from the Home screen.
Adjust Ramping Up and Down durations using the Up/Down cursors and confirm with Enter.
The unit returns to the Home screen after 30 seconds of inactivity or by pressing Restart.

Light Settings

Navigate to the Set Lights screen from the Home screen.
Set the Off and On times for lights using the Up/Down cursors and confirm with Enter.
Adjust Maximum Brightness as needed and confirm with Enter.
The unit returns to the Home screen after 30 seconds of inactivity or by pressing Restart.

Boost Button

Activates lights at 100% for temporary access to the shed.
Press and hold the Boost Button for six seconds to confirm, with options to extend time or return to the Home screen.

Reset for New Flock

Press and hold the Restart Button for ten seconds to reset to Day 1.

Support
For assistance, contact [email protected].

Catalog excerpts

V1.4 DTD Automatic Controller Manual Protocols and Instructions for Poultry Broilers

Open the catalog to page 1

V1.4 DTD Agri Lamp Automatic Controller TM 2 Channel | Basic Mode • SETTING THE CLOCK • SETTING TO A OR B CHANNEL • SETTING THE LIGHTS ON/OFF TIMES & MAXIMUM BRIGHTNESS • SETTING THE F • BOOST BUTTON • RESET TO DAY 1 FOR NEW FLOCK Main Power On Indicator Ramp Up Indicator Ramp Down Indicator • Flashes during ramping cycle • Solid where cycle complete With the Dip Switches set in this configuration the unit is set to 2 Channel basic mode (2 channel and Twin ramp up and ramp down operations) Copyright © All Rights Reserved

Open the catalog to page 2

1. From Home is displayed. screen press down cursor 2. With the Right Cursor to set day press Enter (3 screen.Use the Up/Down cursors screen _J to accept.With the Right Cursor select the Set Hour Use the Up/Down Cursors to set the current Hour press Enter to accept. With the Right Cursor select the Set Minutes screen Use the Up/Down Cursors to set the current Minutes press 3. After 30 seconds of inactivity the unit will return to Home Screen or press Restart return to home screen instantly. SELLECT CHANNEL CHANNEL A_ 2. With the Right Cursor Select the Channel Set screen to set either Channel...

Open the catalog to page 3

1. From Home is displayed. 2. With the Right Cursor Select the Off Hour screen to set the hour you wish the lights to start ramping down press Enter PJj|| to accept. With the Right Cursor select the Off Minutes screen Use the Up/Down Cursors to set the Minutes to start ramping down, press Enter to accept. With the Right Cursor Select the On Hour screen Use the Up/Down cursors to set ept. With the Right Cursor se Use the Up/Down Cursors to set the Minutes to start Use the Up/Down the hour you wish the lights to start ramping up press Enter to accept. With the Right Cursor select the On Minutes...

Open the catalog to page 4

BOOST BUTTON (this temporarily runs lights at 1000/©f personel to access shed) 1. Press and hold Boost tt^ | Button for about six seconds until Boost confirmation screen displays, press Enter to confirm Press enter to add an extra 10 minutes or return back to Home screen. RESET TO DAY 1 FOR NEW FLOCK 1. Press and hold Restart Button for about ten seconds until Restart confirmation screen RESTART ? PRESS displays, press Enter Dl to confirm. Copyright © All Rights Reserved

Open the catalog to page 5

Open the catalog to page 6

MODE 1 With all switches in the down position the unit is set to single channel basic mode. This provides one relay output and one 0-10v output. The Ramp up/ down settings remain the same as set regardless of which day the unit is on. MODE 2 With switch 2 in the up position and all other switches in the down position the unit is set to two channel basic mode. This provides two relay outputs and two 0-10v outputs. The Ramp up/ down settings remain the same as set regardless ofwhich day the unit is on. MODE 3 With switch 1 in the up position and all other switches in the down position the unit...

Open the catalog to page 7

Should assistance be required, email: [email protected]

Open the catalog to page 8

V1.4 DTD Automatic Controller Manual

V1.4 DTD Automatic Controller Manual

Catalog excerpts

All Greengage catalogs and technical brochures