HP6V series
1 / 28Pages

The HP6V series axial piston pumps are designed for high pressure open systems with a specially designed new power structure that is smaller and more resistant to pollution. Installation size ■Variable pump in swash-plate design for open circuit. ■High continuous pressure. ■Exceptional self-priming capability. ■Available with American (SAE) and Japanese (JIS) mounting flanges and shafts. ■Excellent reliability and long life. ■High power to weight ratio. ■Variety of control options. ■Optional through drive. ■Quick control response. ■Low pressure pulsation and low noise. ■Developed for engineering, mobile vehicles, industrial, other industrial application and agricultural machinery.

Piston Pump I HP6V Series Steady state suction pressure should be 0 bar and above(at normal condition); If suction pressure less than 0 bar, Boost pressure should be required; In case of 200-1000mm2/s, please allow system to warm up before using machine; HP6V85 is currently under development and is expected to be launched in May 2025.

Piston Pump I HP6V Series Product series © Product series HP6V Design series © Design series A Series A Seals Seals FKM ( Viton rubber: DIN ISO 1629) NBR (Nitrile rubble :DIN ISO 1629)

Piston Pump I HP6V Series Type introduction Direction of Rotation

Piston Pump ｜ HP6V Series Type introduction Control type Control type Apply to constant displacement pump Only pressure control Electro-hydraulic pressure control,negative control (without suppressor diode) Pressure Load sensing+throttling unloading cut-off Load sensing ⑪ Remotely operated +Electric proportional displacement. Deutsch DT04-2P ; 2 contact pin, (without suppressor diode) Pressure cut-off+ Load sensing+throttling unloading Standard / special version ⑫ Standard version Remark：● = available； ○ = On request； Special version Pressure cut-off+ Load sensing Power Remotely operated...

Regulators introduction 1. Load sensing Standard setting: 15bar Piston Pump ｜ HP6V Series recommended to set it too high. If you need other settings, please consult our company.) 2. Pressure Cut-off Load sensing + Pressure Cut-off The load sensing control is a flow control option that operates as a function of the load pressure to regulate the pump displacement to match the actuator flow requirement. The load sensing control compares pressure before and after the sensing orifice and maintains the pressure drop across the orifice (differential pressure Δp) and with it the pump flow constant....

Piston Pump ｜ HP6V Series Regulators introduction Control Type : 1. Load sensing Standard setting:15bar recommended to set it too high. If you need other settings, please consult our company.) Function and Features: P0 Pressure cut-off The Pressure Cut-off regulator monitors outlet pressure once the pressure reaches the cutoff setting, the pump will return to minimum displacement. Remote Control The pump can be remotely controlled by connecting a relief valve to the PL port of the regulator. The pump can also be unload at a low pressure continue standby condition by using a solenoid valve....

Piston Pump ｜ HP6V Series Control Type : 1. Load sensing Standard setting: 15bar recommended to set it too high. If you need other settings, please consult our company.) 2. Pressure Cut-off Adjustment range: 21 bar-320 bar 3. Torque limiting LP Load Sense and Pressure Cut-off with Torque limiting The L1 control functions as previously noted. In response to a rise in delivery pressure the swash plate angle is decreased, restricting the input torque. This regulator prevents excessive load against the prime mover. The torque limit control module is comprised of two springs that oppose the...

Piston Pump I HP6V Series recommended to set it too high. If you need other settings, please consult our company.) Standard setting: 280bar(HP6V18) Adjustment range: 21bar~215bar(HP6V18) 5. Connector (deutsch) DEUTSCH: DT04-2P The L1 control functions as previously noted. It controls the input torque of the pump by changing different current, specific current is related to certain input torque, thus satisfy needs of different torque on excavator

Piston Pump I HP6V Series Regulators introductionCode: ER □Control Type : Negative electro-proportional pressure control The ER2 valve is set to a certain pressure by a specified variable solenoid current. This causes an increase or decrease in the pump swivel angle (flow) in order to maintain the electrically set pressure level. The pump thus only delivers as much hydraulic fluid as the consumers can take. The desired pressure level can be set steplessly by varying the solenoid current. As the solenoid current signal drops towards zero, the pressure will be limited to Pmax by an adjustable...

Piston Pump I HP6V Series HP6V18 installation sizePort Details

Piston Pump ｜ HP6V Series Installation size HP6V18 Mounting Flange HP6V18 Input Shaft type 43 "S" type spline shaft "S0" type spline shaft

Piston Pump I HP6V Series HP6V28/35 installation sizePort Details

Piston Pump ｜ HP6V Series Installation size HP6V28/35 Mounting Flange HP6V28/35 Input Shaft type 41

Piston Pump I HP6V Series Installation size Displacement is adjustable HP6V47 with Cut-off/Load Sense Control with torque limit (Clockwise Rotation) For the CCW pump just reverse the inlet and outlet port. Port Details

Piston Pump ｜ HP6V Series Installation size HP6V47 Input Shaft type 41 "S1" type spline shaft "S2" type spline shaft ISO straight shaft SAE J744-25-1 (non axial) B6.35×32 straight shaft (Used together with A flange) "K2" type straight shaft

Piston Pump I HP6V Series

Piston Pump ｜ HP6V Series Installation size HP6V65 Mounting Flange

Installation size Piston Pump ｜ HP6V Series "K2" type straight shaft

Piston Pump I HP6V Series HP6V76 with Cut-off/Load Sense Control with torque limit

Piston Pump ｜ HP6V Series Installation size HP6V76 Mounting Flange

Piston Pump ｜ HP6V Series Installation size HP6V76 Mounting Flange 217 .5 0 "S2" type spline shaft HP6V76 Input Shaft type "S3" type spline shaft 47 ISO straight shaft (non axial) (Used together with A flange) "P" type straight shaft