Models IH 2055 , IH 2090 , IH 2013 Classic & Flex Operator’s Manual Read this Operator's Manual carefully and make sure you understand it before attempting to use the Iron Horse.

Trouble shooting ………………………….

Introduction This Operator's Manual describes in detail how the Iron Horse is used, maintained and how servicing is to be carried out. It also describes the measures to be taken for maximum safety, how the safety features are designed and work, as well as their inspection and any repairs that may result. NOTE! The section dealing with safety must be read and understood by all those who install, use or repair the Iron Horse. The Operator's Manual describes getting started, use and the different maintenance procedures that can be carried out by the user. More comprehensive servicing or trouble...

The symbols below are used on the Iron Horse The following decals with symbols can be found and in this Operator's Manual. on the Iron Horse. Engine Stop Helmet, hearing protection and eye protection should be used. Stop control on the engine Brake locked Gloves must be worn. Boots or work shoes with steel toe-caps and non-slip soles should be worn. Brake open Parking brake Read this Operator's Manual carefully and make sure you understand it before attempting to use the Iron Horse. Fast Slow Clutch Choke Fuel tap Differential Forward Reverse Engaged Disengaged Exercise caution. Keep your...

Safety Regulations Safety during use The safety regulations that apply while using the Iron Horse are documented in respective areas under the section ”Use” on page 24 - 27. Warning! An IronHorse can be a dangerous machine that can cause serious or fatal injury if used incorrectly or carelessly. It is very important that the person using the IronHorse reads and understands the content of this manual. Personal protective equipment The person or persons using the Iron Horse or remaining in its close proximity must be equipped with the personal equipment as set out below: 1. Helmet with hearing...

Iron Horse safety equipment_ WARNING! The IronHorse must never be used if any of the safety devices or guards are missing, damage or do not work There are a number of safety devices and guards to prevent accidents with the Iron Horse. These are described in the general description of Iron Horse. See page 16. The safety devices and guards also require regular inspection and maintenance. These measures and intervals are set out in the ’’Maintenance” section. See pages 28-34. Safety during use The safety regulations that apply while using the Iron Horse are documented in respective areas under the...

14. Lever for log bunk 15. Front bogie wheel 16. Drive wheel 17. Storage box 18. Roll-over bar 19. Screw for height setting 20. Belt guard 21. Protective plate 22. Adjusting bolt for steering arm 23. Balance spring for steering arm 24. Cable cover 25. Differential lock 26. Manual winch 27. Gear lever 28. Fuel tank 29. Chain saw attachment 30. Petrol engine Iron Horse IH 2055 - IH 2013 Classic The Iron Horse consists of the following main parts: • Engine, gearbox and transmission • Chassis • Caterpillar track • Steering arm Description: 11. Tension wheel bearing 12. Rear bogie wheel 13. Cover...

12. Cover over track 13. Front bogie wheel 14. Drive wheel 15. Belt guard 16. Protective plate 17. Adjusting bolt for steering arm 18. Balance spring for steering lever 19. Cable cover 20. Differential lock 21. Gear lever 22. Fuel tank 23. Chain saw attachment 24. Petrol engine 25. Adjustable accessory mount 26. Hydraulic piston 27. Steering arm hydraulic piston 28. Hydraulic pump 29. Hydraulic tank Iron Horse IH 2090 - 2013 Flex The Iron Horse consists of the following main parts: • Engine, gearbox and transmission • Chassis • Caterpillar track • Steering arm Beskrivning: 10. Tension wheel bearing...

Description: 32. Open ended spanner 10 - 13 33. Open ended spanner 17 - 19 34. Spark plug spanner 35. Allen key 4 mm. 36. Allen key 6 mm. 37. Track adjustment tool 38. This Operator's Manual Decal placement The following warning and information decals can be found on the machine. Missing or illegible decals must be replaced.

Iron Horse (FIG. 2) The Iron Horse consists of the following parts: Note! Some parts are optional and are not included as standard. • Chassis with mounts for the drive unit, log bunk, bogie and caterpillar track. • Load anti-slip guard. • Load anti-slip guard with integrated power winch. • Manual winch. The drive unit consists of the following parts: • Engine with muffler and fuel tank • Variator. • Gearbox with mounts for the steering arm and drive axles. • Dog clutch • Steering brake. The steering arm consists of the following parts: • Handlebars with controls • Adjustable spring for weight...

Load anti-slip guard (FIG. 5) The Iron Horse is equipped with a load anti-slip guard (with exception of the standard model). The load anti-slip guard prevents the load from shifting and damaging the engine. Tubes are fitted to the guard that act as overriders to prevent brush and branches damaging the engine. There is also a chain saw attachment fitted to the overrider tubes and a bracket to hang the combi-container for the chain saw. A toolbox is also fitted on the guard. Load anti-slip guard with integrated power winch (FIG. 6) The power winch is fitted on the load anti-slip guard. The power...

Engine (FIG. 8) The Iron Horse is driven by a powerful petrol engine. There are three engine options to choose from. The engine is mounted above the gearbox and is connected to the gearbox via a belt transmission. The fuel tank and muffler with an integrated heat shield are also fitted to the engine. The engine's throttle is operated from the handlebars. The stop switch is easily accessible on the front of the engine (FIG. 8 A). The engine is also equipped with a fuel tap and choke. Variator (Torque converter) (FIG. 9) The Iron Horse is equipped with a variable gear device, variator (torque converter)...