D65
232Pages

Parts Catalog 147934 Revision A Original Instruction

Draper Header for Combines and Self-Propelled Windrowers NOTE: Keep your MacDon publications up-to-date. The most current version can be downloaded from our website (www.macdon.com) or from our Dealer-only site (https://portal.macdon.com) (login required). A Russian translation of this manual can be ordered from MacDon, downloaded from the MacDon Dealer Portal (https://portal.macdon.com) (login required), or downloaded from the MacDon international website (http://www.macdon.com/world).

Introduction This Parts Catalog lists all the replacement parts that can be ordered for a MacDon D65 Draper Header for Combines and Self-Propelled Windrowers. When ordering, be sure the complete and proper part number is given. Some parts vary with header size; be sure you are ordering the correct part number for your unit. Bold text is used to indicate updates made at the current revision level. With each new revision of the catalog, previous revisions are returned to regular text. In this catalog, right-hand (RH) and left-hand (LH) are determined from the operator’s seated position in the...

Abbreviations A/R – as required (quantity varies) BHRN – button head rib neck C/W – complete with CCW – counterclockwise CW – clockwise CSK – countersink DK – double knife DT – distorted thread FLG – flange HDR – header HYD – hydraulic MFA – manual fore–aft I.D. – inside diameter LG – long LH – left hand (determined from operator's position, facing forward) HFA – hydraulic fore–aft NC – national coarse thread NF – national fine thread NSS – not serviced separately O.D. – outside diameter OPT – optional REF – reference, part number called up elsewhere in catalog RH – right hand (determined...

This list covers changes made since the last revision (147724 Rev. A).

HEADER FRAME, DIVIDERS, AND SHIELDS Header Frame, Dividers, and Shields

HEADER FRAME, DIVIDERS, AND SHIELDS Excludes: 15-30 ft. Single, Single Reel, 35 ft. Single, Single Reel, 35 ft. Double, Single Reel. Includes: 15-30 ft. Single, Single Reel, 35 ft. Single, Single Reel, 35 ft. Double, Single Reel. For endshield decals, refer to Section 29 Product Identification Decals, page 117.

HEADER FRAME, DIVIDERS, AND SHIELDS

HEADER FRAME, DIVIDERS, AND SHIELDS 8. Standard divider rod shown. For rice divider rods, refer to Section 44 (Option) Rice Divider Rods, page 155. Required to properly install wobble box mount (MD #123751 or 123752), comes complete with instructions. See your MacDon Dealer for more information. 12. Refer to Section 46 (Option) Short Brace Kit for Center Reel Arm / Divider Latches, page 159.

HEADER FRAME, DIVIDERS, AND SHIELDS

HEADER FRAME, DIVIDERS, AND SHIELDS Part Number SCREW – HEX WASH HD THD ROLLING 3/8 NC X 5/8 NUT – FLANGE DT SMOOTH FACE 0.375-16 UNC WASHER – FLAT SCREW – SELF TAP HEX WASH HD 1/4 NC X 1/2 WASHER – HARDENED Serial Number WASHER – FLAT NUT – FLG LOCK SM FAC

GUARDS AND HOLD-DOWNS – SINGLE-KNIFE HEADERS Guards and Hold-Downs – Single-Knife Headers

GUARDS AND HOLD-DOWNS - SINGLE-KNIFE HEADERS NOTE: Top of illustration shows pointed guards; bottom shows stub guards. 13. Includes cutterbar wearplate (MD #129297) and hardware. Kits available through Whole Goods only. 14. Quantities: 20 ft. = 35, 25 ft. = 45, 30 ft. = 55, 35 ft. = 65, 40 ft. = 75, 25 ft. with stub ends = 42, 30 ft. with stub ends = 52. 16. Quantities: 25-30 ft. = 6, 20 ft. with stub ends = 38, 25 ft. with stub ends = 48, 30 ft. with stub ends = 58, 35 ft. with stub ends = 68, 40 ft. with stub ends = 78. 17. Quantities: 25 ft. with stub ends = 21, 30 ft. =...

GUARDS AND HOLD-DOWNS – SINGLE-KNIFE HEADERS

GUARDS AND HOLD-DOWNS - SINGLE-KNIFE HEADERS NOTE: Top of illustration shows pointed guards; bottom shows stub guards. 20. Used with stub guards and sheet metal hold-downs. Includes two covers, hardware, and instructions. 21. Used with pointed guards and forged hold-downs. Includes two covers and hardware. 23. First four guards on the drive end of single-knife headers with pointed guards include one of item #1, end guard (MD #118301), and three of item # 3, special guard (MD #118345). See your MacDon Dealer for more information. 24. First four guards on the drive end of single-knife headers...

GUARDS AND HOLD-DOWNS – DOUBLE-KNIFE HEADERS Guards and Hold-Downs – Double-Knife Headers

GUARDS AND HOLD-DOWNS - DOUBLE-KNIFE HEADERS NOTE: Top of illustration shows export heads; middle shows stub guards; bottom shows pointed guards. 27. Includes cutterbar wearplate (MD #129297) and hardware. Kits available through Whole Goods only. 28. Double-knife headers. Kits available through Whole Goods only.

GUARDS AND HOLD-DOWNS – DOUBLE-KNIFE HEADERS

GUARDS AND HOLD-DOWNS - DOUBLE-KNIFE HEADERS NOTE: Top of illustration shows export heads; middle shows stub guards; bottom shows pointed guards. 35. First four guards on the drive ends for double-knife headers with stub guards include four of item #5, stub guard without wear bar (MD #118347), for each drive end (LH and RH). See your MacDon Dealer for more information. 36. First four guards on the drive ends for double-knife headers with pointed guards include one LH end guard (MD #118301) and three special guards (MD #118345) for the LH drive end, and one RH end guard (MD #118302) and...

KNIFE COMPONENTS AND KNIFEHEAD Knife Components and Knifehead

KNIFE COMPONENTS AND KNIFEHEAD NOTE: Top of illustration shows single-knife; bottom shows double-knife. NOTE: To service knife assemblies refer to the following sections: 5 Segmented Knives - Single-Knife Headers, Fine-Tooth Sections, page 19 6 Segmented Knives - Single-Knife Headers, Coarse-Tooth Sections, page 21 7 Segmented Knives - Double-Knife Headers, Fine-Tooth Sections, page 23 8 Segmented Knives - Double-Knife Headers, Coarse-Tooth Sections, page 27 37. Quantities (individual sections): 15 ft. = 57, 20 ft. = 77, 25 ft. = 97, 30 ft. = 117, 35 ft. = 137, 40 ft. = 157. 38. 30-45 ft....