Parts Catalog 214384 Revision A Original Instruction

M1240 Windrower, featuring Dual Direction® and Crossflex™ rear suspension Published September 2017 NOTE: Keep your MacDon publications up-to-date. The most current version can be downloaded from our website (www.macdon.com) or from our Dealer-only site (https://portal.macdon.com) (login required).

Introduction This Parts Catalog lists all the replacement parts that can be ordered for a MacDon M1240 Windrower. Bold text is used to indicate updates made at the current revision level. With each new revision of the catalog, previous revisions are returned to regular text. In this catalog, right-hand (RH) and left-hand (LH) are determined from the operator’s position, facing forward with the windrower in cab-forward position. An arrow is sometimes used in illustrations to indicate cab-forward position as shown below.

The side of the serial number on which the dash (-) appears determines whether the part is used "up to" or "after" the serial number given. Example: • -162249 Used on machines up to and including serial number 166249. • 166250- Used on machines including and after serial number 166250.

Abbreviations The following abbreviations are used in this catalog. A/R – as required (quantity varies) ASSY – assembly C/W – complete with CSK – countersink DK – double knife DT – distorted thread EXT – exterior FLG – flange HH – hex head HYD – hydraulic I.D. – inside diameter LH – left hand (determined from operator's position, facing forward) NC – national coarse thread NF – national fine thread NSS – not serviced separately O.D. – outside diameter OPT – optional RD – round REF – reference, part number called up elsewhere in catalog REG – regular RH – right hand (determined from operator's...

This list covers changes made since the last revision (214055 Rev. A)

WHEEL LEGS Part Number STEP – WINDSHIELD ACCESS ASSY – LEG PIN REMOVAL TOOL WASHER – FORMED WASHER – FLAT

2 Left-Hand Platform and Toolbox

LEFT-HAND PLATFORM AND TOOLBOX Includes tool box with tray, tool box transition kit, and instructions.

3 Left-Hand Platform Mechanism

LEFT-HAND PLATFORM MECHANISM Part Number BRACKET – HINGE WELDT SPRING – COMPRESSION SUPPORT – LATCH, PLATFORM ASSY – STIRRUP LATCH SUPPORT – PLATFORM, WELD'T TUBE – HINGE BUSHING – BRONZE LINK – PLATFORM BOLT – STRIKER SCREW – CSK MACH FLAT SOC HD M8 X 30 GR 5 ZP WASHER – FLAT LARGE M8-200HV-A2L

RIGHT-HAND PLATFORM Part Number LATCH – STEP SPRING – COMPRESSION RAIL – RH REAR, BLACK CLIP – LOCK SUPPORT – BUMPER BUMPER – RUBBER STUD – BALL (M10), M8 THREAD MEMBER – FLEXIBLE STEP PLATE – WASHER FLEX STEP ANGLE – RAIL MOUNT BOTTOM, BLACK

5 Right-Hand Support and Tanks

RIGHT-HAND SUPPORT AND TANKS Includes drain fitting (MD #204080), cap (MD #207374), barbed fitting (MD #21046), hose (MD #205473), one filter (MD #111608), and three clamps (MD #136743). Includes gasket and five screws. For service parts refer to Section 6 Diesel Exhaust Fluid (DEF) Tank, page 13.

RIGHT-HAND SUPPORT AND TANKS

RIGHT-HAND SUPPORT AND TANKS 7. Bolts attach to RH platform support MD #207591.

6 Diesel Exhaust Fluid (DEF) Tank

DIESEL EXHAUST FLUID (DEF) TANK Serial Number ASSEMBLY – SCREEN, FILL NECK FILL NECK, LESS CAP PLUG – DRAIN C/W GASKET VALVE – AIR VENT VALVE S/A FLANGE – SAE 6 HOLE TANK GROMMET – LARGE, DEF HEAD HOUSING – LIQUID FILTER, S/A FILTER – SUCTION O-RING – DEF TANK FILL NECK, 2.51 IN O.D., 2.19 IN I.D. 8. Refer to Section 5 Right-Hand Support and Tanks, pa

7 Diesel Exhaust Fluid (DEF) Plumbing

DIESEL EXHAUST FLUID (DEF) PLUMBING 9. Part serviced through Cummins, contact your Cummins dealer. Cummins part #4387304.

DIESEL EXHAUST FLUID (DEF) PLUMBING

DIESEL EXHAUST FLUID (DEF) PLUMBING

WALKING BEAM 10. Includes two bushings (MD #204758) and decal (MD #207087). Refer to Section 103 Decals - Information and Reflectors, page 263. 11. Includes lube fitting (MD #18671), two bushings (MD #202661), and decal (MD #23165). Refer to Section 103 Decals - Information and Reflectors, page 263.

12. Kits available through Whole Goods only. 13. Includes ball bearing (MD #208687) and lube fitting (MD #18671).

Drive Wheels and Tires 2

DRIVE WHEELS AND TIRES 14. Kits available through Whole Goods only. 15. Includes decals (MD #111221, 166454, 166727, and 291411).

LIFT LINKAGE Part Number ARM – FLOAT LINK ASSEMBLY 18 BEARING – NEEDLE SPACER – SHORT SHIM – LINKAGE FITTING – LUBRICATION 1/4-28 TAPER THD ASSEMBLY – SPRING ARM – SPRING LINK WELDT TUBE – PIVOT RING – EXT RETAINING HEAVY DUTY LEVER – FLOAT TENSIONER WELDT BUSHING – COMPOSITE CYLINDER – FLOAT ADJUST SEAL KIT – CYL. FLOAT ADJUST Serial Number 16. Includes decals (MD #23165, 166438). 17. Includes decals (MD #23165, 166439). 18. Includes four bearings (MD #112789), two spacers (MD #163310),

LIFT LINKAGE

LIFT LINKAGE

13 Lift Linkage Cylinders

LIFT LINKAGE CYLINDERS Part Number LOCK – CYLINDER STOP WELDMENT RETAINER – CYLINDER STOP CHANNEL – LOCK RELEASE, M10 ASSEMBLY – SHAFT WITH HANDLE GRIP SPRING – COMPRESSION CYLINDER – LIFT, MASTER KIT – LIFT CYL SEALS, MASTER 19 CYLINDER – LIFT, SLAVE KIT – LIFT CYL SEALS, SLAVE 19 FITTING – ADAPTER 6 MORFS X 8 MORB SUPPORT – HEIGHT SENSOR ARM – HEIGHT SENSOR PROFILE SENSOR – ANALOG HALL EFFECT FITTING – ELBOW 90° HYD C/W O-RING Serial Number

LIFT LINKAGE CYLINDERS

LIFT LINKAGE CYLINDERS

FLOAT SENSORS Part Number SUPPORT – SENSOR MOUNT ROTARY SENSOR – DUAL OUTPUT BALL JOINT – RH THREAD BALL JOINT – LH THREAD