FPS-JD 1026 R
19Pages

Original operating manual FPS-JD 1026 R 131 8140 Front Power System 131 8479 Front PTO shaft 131 7454 Hydraulic Extension Kit 131 7456 Mower Attachment Kit

About this operating manual About this operating manual Dear customer! Thank you for purchasing this implement, we appreciate your trust. Prior to using this implement for the first time, read this operating manual carefully and conscientiously all the way through. To obtain the long service life for which matev products are known, careful and conscientious maintenance is a strict requirement. However for proper maintenance it is strictly necessary that you have carefully read this operating manual. Moreover, it is not possible for matev to assume liability for damage that is attributed to...

Safety Guidelines and instructions with which you must comply, are summarized in this section. Personnel who install, operate and maintain these implements, must have read and understood this operating manual. Intended use The front power system must only be mounted on type John Deere 1026 R tractors. The front power system is used for accommodating small to medium-sized implements, such as snow blades, sweepers, etc. and should only be connected and operated with such implements. Please note that you must avoid overloading the front axle, even in heavyduty implementation (e.g. snow...

Qualifications of personnel Only persons 18 years of age or older, or instructed persons should install, operate, and maintain the implements. The operator must have read and understood this operating manual. General safety notices General safety instructions are explained in this section. These safety instructions are used in the subsequent chapters. In addition to the safety aspect, you will save money and work time if you follow these safety instructions. Danger! Severe injury to the operator or third parties occurs. Comply with the safety notice. Attention! Minor injury of the operator...

Special safety notices The safety instructions specified in this chapter are also affixed as stickers on the implements. Attention! Danger of injury due to moving parts. Remove the ignition key before performing maintenance tasks on the implement. Attention! Injuries can occur due to improper operation. The implement can be damaged. Read the operating manual all the way through. Comply with the safety instructions. Attention! Injuries due to fluid escaping under high pressure. Comply with the notice in the operating manual.  Attention! Danger of crushing due to moving parts. Never reach...

Switch off the tractor and remove the ignition key. Enter the vehicle chassis number of the front power system in section 6 of this operating manual. Installation of the front power system Start the installation by fitting the two-piece attachment bracket on the front on the tractor frame. The attachment bracket is fastened on the tractor frame on the front and side with the bolts included in the scope of delivery. Attachment bracket The actual front power system is only hooked into the provided aperture on the attachment bracket with the cross-member of the front power system and locked...

Arrest nuts Angle bolts Fig. 2: Locking mechanism of the front power system Installation of the front PTO shaft (drive shaft tube) For installation of the front PTO shaft, pre-assemble the drive shaft with the drive shaft holder and the protective pot. Then pull out the arrest bar (included in the scope of delivery of the attachment bracket) and slide the pre-assembled drive shaft holder into the attachment bracket. lay rubber between

Comply with the instructions in the operating manual provided by the manufacturer of the universal joint shaft. Mount the universal joint shaft as described in the original manual provided by the manufacturer of the universal joint shaft. Switch off the tractor and remove the ignition key before mounting or dismounting the front PTO shaft. Insert the universal joint shaft through the protective tube and press the locking pin (locking ring) on the outer fork. Keep the locking pin depressed. Install the hinge shaft with the sliding part forward Slide the outer fork onto the profile stub of...

Fix the front protective tube on the front protective tube holder with screws and with the rubber strap on the rear. The front protective tube holder is also fastened on the drive shaft. The rear protective tube holder must be mounted on the underside of the tractor, as shown in the following photo. Fig. 6: Protective tube holder, front Fig. 7: Protective tube holder, rear

Mounting the rear hydraulic extension kit Mount the holder with the connection plugs on the front of the front power system (tapped bores are present) and lay out the hydraulic hoses along the tractor frame and connect them to the connections available on the tractor side. Holder with connection plugs, front Fig. 10: Hydraulic extension set, rear

Mounting the rear mower attachment kit The mower attachment kit is already integrated in the attachment bracket of the front power system. To attach the mid-mount mower, the front power system must be unhooked.

Operation Before starting up the implement, read the instructions on safety and handling for operation of the entire implement and connection to the tractor. In addition, prior to start-up you must ensure that the vehicle meets the requirements specified in the German Road Traffic Vehicle Licensing Act. The front power system should only be placed in service if all safety devices are attached and fully functional. Prior to starting work the operator must familiarize himself with the device and ensure for himself that the entire device is operationally reliable. Moving objects and fixtures,...

Coupling and uncoupling implements Comply with the axle loads specified by the tractor manufacturer. Drive the tractor forward in front of the implement. Lower the front power system hydraulically. Drive slowly toward the implement until the coupling triangle of the tractor is under the coupling triangle of the implement. Slowly lift the front power system until the implement is slightly lifted. Secure the implement with the appropriate triangle locking mechanism. The triangle locking mechanism depends on the type of implement. Lowering safeguard for the front power system Use the lowering...