FPS –Kubota RTV X900
17Pages

Original Operating Manual FPS –Kubota RTV X900 Front power system Front hydraulic extension kit For use of the front power system and hydraulic extension kit, the Kubota RTV X900 must be equipped with the following accessories from Kubota. - Hydraulic pump for supplemental hydraulics (K759199340) Hydraulic valve, double-acting / double-acting with float setting (K759199360)

About this operating manual Dear customer! Thank you for purchasing this implement, we appreciate your trust. Prior to using this implement for the first time, read this operating manual carefully and conscientiously all the way through. Keep this operating manual where it is easily accessible. This will enable you to refer to important information and handling instructions as needed. Listings with bullet points are marked as follows:  Text  Text  Text Handling instructions are marked in the sequence in which they should be executed, as follows: 1. 2. 3. Text Text Text This implement is...

The front power system is not suitable for lifting people or for use as a work platform! All other uses are excluded. Non-intended use causes:    Health hazards for the operator or for third parties Damage to the tractor and the implements Environmental damage Qualifications of personnel Only personnel 18 years of age or older, or instructed personnel should install, operate, and maintain the implements. The operator must have read and understood this operating manual. General safety notices General safety instructions are explained in this section. These safety instructions are used in...

Special safety notices Safety instructions are specified in this chapter that are also affixed as stickers on the implements. Attention! Danger of injury due to moving parts. Remove the ignition key before performing maintenance tasks on the implement. Attention! Injuries can occur due to improper operation. The implement can be damaged. Read the operating manual all the way through. Comply with the safety instructions. Attention! Injuries due to fluid escaping under high pressure. Comply with the notice in the operating manual. Attention! Danger of crushing due to moving parts. Never reach...

Installation / operation Installation For use of the front power system and hydraulic extension kit, the Kubota RTV X900 must be equipped with the following accessories from Kubota. - Hydraulic pump for supplemental hydraulics (K759199340) - Hydraulic valve, double-acting / double-acting with float setting (K759199360) Danger! Severe injury to the operator or third parties occurs. Switch off the tractor and remove the ignition key before mounting or dismounting the implements. Note! Enter the chassis number of the front power system in section 5.3 of this operating manual. Installation of...

Installation / operation Upper bolt-on points: With the aid of the counter-plate the front power system is clamped onto the frame with four bolts. Fig. 2: Upper four bolt-on points from the front (two are covered, see photo below) Fig. 3: Upper four bolt-on point from the side

Installation / operation Install cylinder and top link in the front power system Important: Cut off the handle on the top link!!! Fig. 5: Remove the handle on the top link Mount the holder for plug couplings on the front power system Fig. 6: Holder for plug couplings Dismount floor panels Fig. 7: Dismount floor panels

Installation / operation Attention! Injuries due to fluid escaping under high pressure. Comply with the notice in the operating manual. Install the hydraulic lines in such a manner that any risk of damage due to the wheel or the front axle is excluded. Also check the installation of the lines at full steering travel of the wheels and oscillation of the front axle in both directions. Connect the hydraulic lines to the cylinder and connect the hydraulic lines to the tractor's hydraulic system. Fig. 8: Installation of the hoses of cylinder (front view driver side) (arrow shows direction of...

Installation / operation Fig. 10: Lay out hoses (arrow shows direction of travel) 2x hoses of the front power system or hydraulic extension kit Fig. 11: Connect hoses (arrow shows direction of travel)

Installation / operation Fig. 12: Connect hoses (arrow shows direction of travel) Connections for hydraulic extension kit 7. Connections for front power system Connect the hydraulic sockets + the hydraulic lines on the holder, connect them with tractor's hydraulic system, as shown in the photo above. Fig. 13: Hoses of the hydraulic extension kit (front view driver side) (arrow shows direction of travel)

Installation / operation Re-mount floor panels Operation Attention! Before starting up the implement, read the instructions on safety and handling for operation of the entire implement and connection to the tractor. Coupling and uncoupling implements Note! Comply with the axle loads specified by the tractor manufacturer Drive the tractor forward in front of the implement. Lower the front power system hydraulically. Drive slowly toward the implement until the coupling triangle of the tractor is under the coupling triangle of the implement. Slowly lift the front power system until the...

Disposal / guarantee Note! Use the lowering safeguard for: – Road travel – Driving between work locations – Cleaning and maintenance tasks Attention! Check all threaded unions prior to using the implement and after using the implement. Loosened connections must be re-tightened. Damage can occur. Note! Strictly avoid lowering the front power system via the tractor's control lever when the lowering safeguard is locked. This could damage parts of the front power system! General information Attention! Personal injury or damage to the tractor and the implements can occur. Before each use check...

Disposal / guarantee After 25 operating hours, at the start of the season, or after a longer standstill period: Attention! Danger of injury due to moving parts. Remove the ignition key before performing maintenance tasks on the implement. Grease the moving parts of the implement Grease the bearings. Check the seat, status and seal of the hydraulic lines Before and after each use check all threaded unions for firm seat and re-tighten them if necessary Repair If there are faults, problems, or other indications of malfunction, contact your sales consultant or contact the manufacturer directly:...