Front power lift FPS-JD 3036
25Pages

Original Operating Manual Front power lift FPS-JD 3036 Front power lift 131 7161 Joystick set triple 131 7136 Joystick set single 131 7160 Conversion kit orig. JD frontloader 131 7224

About this operating manual About this operating manual Dear customer! Thank you for purchasing this device, we appreciate your trust. In order to optimally use your new front power lift it is necessary to read this operating manual completely and conscientiously and to understand it before first use of the device. To obtain the long service life that matev products are known for, careful and conscientious maintenance is a strict requirement. To properly maintain your front power lift it is strictly necessary that you have carefully read this operating manual. Moreover it is not possible...

Guidelines and instructions with which you must comply are summarized in this section. Personnel who install, operate and maintain the device, must have read and understood this operating manual. Intended use The front power lift should only be mounted on type JD 3036 tractors, it is used for accommodating small to medium-sized implements, such as snow blades, sweepers, etc. and should only be connected and operated with such implements. Please note that you must avoid overloading the front axle even in heavy-duty implementation (e.g. snow removal). The permissible axle load is specified in...

Qualification of personnel Only persons 18 years of age or older, or instructed persons should install, operate, and maintain the implements. The operator must have read and understood this operating manual. General safety instructions General safety instructions are explained in this section. These safety instructions are used in the subsequent sections. In addition to the safety aspect, you will save money and work time if you follow these safety instructions. Danger! Severe injury to the operator or third parties occurs. Follow the safety instruction. Attention! Minor injury to the...

Special safety instructions Safety instructions are specified in this chapter that are also affixed as stickers on the implements Attention! Danger of injury due to moving parts. Remove the ignition key before performing maintenance tasks on the implement. Attention! Injuries can occur due to improper operation. The implement can be damaged. Read the operating manual all the way through. Comply with the safety instructions. Attention! Injuries due to fluid escaping under high pressure. Comply with the instructions in the operating manual. Attention! Danger of crushing due to moving parts....

Installation Danger! Severe injury to the operator or third parties occurs. Switch off the tractor and remove the ignition key before mounting or dismounting the implements. Note! Enter the chassis number of the front power lift in section 6, page 23 of this operating manual. Mounting the front power lift Delivery status Fig 1: Lift unit with hydraulic cylinders Cylinder connections

Preparation Before you mount the front power lift on the frame of the tractor it is necessary to drill 3 tapped holes on each side of the frame. The precise position of the individual bores is shown in Fig 3. Fig 3: Mounting bores in the tractor frame The bore diameter for the A-marked bores is 16 mm, and the bore diameter for the Bmarked bore is 12 mm. 3.1.3 Mounting the front power lift Position the front power lift correctly relative to the tractor. Bolt the front power lift to the tractor frame on both sides with the 2 rear screws (see Fig 4). Threaded union Fig 4: Fastening on the...

Side plates Upper link holder Fig 5: Side plates & upper link holder Fit the cylinders on the side plates. Bring both parts together in the correct position and bolt the side plates to the tractor frame and basic implements with 4 bolts on each side (see Fig 6). Fig 6: Bolting the side plates Bolt the upper link holder to the tractor frame inside on the front. For use with a frontloader the upper link must be mounted on the outside. Fig 7: Installation of the upper link holder 6. Use bolts to fasten the free end of the cylinder to the lift shackle of the basic implement (Fig 8).

Secure the bolt with the lock screw. Bolt with lock screw Fig 8: Cylinder installation with lift shackle 8. Connect the hydraulic hoses to both cylinders and connect the hydraulic hoses to the tractor's hydraulic lift. Attention! Connect the hydraulic hoses in such a manner that the hoses coming from the stop valve are connected to the bottom of the cylinders. Stop valve Fig 9: Installing and connecting the hydraulic hoses 9. Route the hydraulic hoses for the left cylinder directly through and behind the engine (see Fig 10 and 11). Hydraulic hose Fig 10: Install the hydraulic hoses, right...

Hydraulic hose Fig 11: Install the hydraulic hoses, left side Mounting the upper link holder Bolt the upper link holder to the tractor frame outside on the front. The upper link holder does not need to be removed for operation with frontloader. Upper link holder, outside Fig 12: Installation of the upper link holder Dismounting the lift arms The lift arms, the coupling support and the upper link must always be removed for operation with frontloader. To dismount the lift arms you must remove the fastening screw and the bolt.

Lift arm Fastening screw with nut Bolt with linch pin Mounting an original JD hood guard To mount a John Deere hood guard as shown in Fig 14 it is necessary the align the fastening points on the front power lift. To do this we recommend the use of our conversion kit for JD frontloaders (see Fig. 17, article no. 131 7224) Mark and drill two tapped bores as shown in the Fig below. The bore diameter is 13 mm.

Fig 15: Bores in the hood guard 2. Cut off the original fastening lugs. See the line in Fig 16 for the precise position of a separating cut. Fig 16: Separating cut line on the hood guard 3. To connect the hood guard with the tractor frame, bolt the lugs on the hood guard to our adapter plates as shown. Fig 17: Conversion kit, adapter plate 4. Now bolt the front power lift to the tractor frame as usual.