MOW-HM 140/160/190 CM Operating Manual Front Mower matev GmbH Nürnbergerstr. 50 90579 Langenzenn, Germany Tel.: +49 (0) 9101 90870 Modifications and errors excepted! Version: 2020-17-11 Reference number: BA-MOW-32068

Order numbers Order No. MOW-H/M 140 CM Mower deck with fixed frame MOW-H/M 160 CM Mower deck with fixed frame MOW-H/M 160 CM Mower deck with hydraulic driving frame MOW-H/M-190 FM basic unit inclusive knives MOW-H/M 140 CM Mower deck with fixed frame MOW-H/M 160 CM Mower deck with fixed frame MOW-H/M 190 CM Mower deck with fixed frame MOW-H/M 160 CM Mower deck with hydraulic driving frame MOW-H/M 160 CM Mower deck with fixed frame MOW-H 160 MC 130 front mower Kärcher with hydraulic driving frame MOW-H 160 MC 130 MU front mower Kärcher with fixed driving frame MOW-H 160 MC 130 MU front mower Kärcher...

We welcome you to the matev family and thank you for purchasing a matev GmbH product, we appreciate your trust. You have acquired a quality product, if contrary to expectations you should have problems with the implement, contact your responsible sales partner. Company stamp – sales partner Before using the product for the first time, please read this operating manual carefully and conscientiously all the way through. The manual describes the handling of the implement in detail and will support you in working safely and effectively. For damage that occurs due to improper use, we will not accept...

About this operating manual Prior to first use, read the manual carefully and conscientiously all the way through. Keep this manual where it is easily accessible. This will enable you to refer to important information and handling instructions as needed. At transfer of the machine the owner of the machine receives instruction in the operation and maintenance of the machine from the owner's sales partner. The owner must ensure that operating and maintenance personnel have been instructed in full scope in the operation and maintenance of the machine. Listings with bullet points are marked as follows:...

Technical data Technical data Cutting height from - to With hydraulic frame Cutting height from - to With rigid frame Dimensions (L/W/H) in mm Cutting width Required minimum capacity of the carrier vehicle Gear oil / lubricating grease Gearbox fill quantity 0.8 l Viscosity class 90, e.g. Shell Spira MB90 After the first 50 h, then every 500 h Gear oil change Lubricating grease All purpose grease with a temperature resistance from -30 °C to +130 °C, for example, mineral-based, lithium universal lubricating grease or similar products. Possible drive configuration 1,000 rpm CW/CCW Front PTO shaft...

Power diagram, hydraulic Please use the diagram below to assess whether your vehicle has enough hydraulic power available. 1. Add the power specifications of all options present on your machine. 2. Be aware of the information concerning the hydraulics of your vehicle. As a rule, the hydraulic power of your vehicle that is available for additional implements, is considerably lower than the engine power. 3. Enter the information in the table below: Example: maximum hydraulic pressure on the vehicle 150 bar. Oil volumetric flow of 40 l/min. equals a maximum hydraulic power of 8.8 kW. Fig. 2: Hydraulic...

General safety notices Guidelines and instructions that you must comply with when dealing with machines are presented in this section. Presentation of the general safety notices The safety notices used in the text employ pictograms and signal words, which in combination indicate the severity of the risk to be expected. Dangerous situations that can directly result in severe or fatal injuries. Dangerous situations that can possibly result in minor injuries or material damage. Recommendations or information for the operator. Read this note. It facilitates your work. Intended use To avoid misuse,...

4.3.1 Qualifications of personnel Installation and maintenance tasks involving safety-relevant parts must only be executed by personnel with the following qualifications:     They must have a technical education, such as agricultural machine mechanic, auto mechanic, etc. Persons without qualified training must be supervised by a person with qualified training. They must have read and understood this operating manual. They must be aware of the relevant safety regulations (accident prevention). 4.3.2 Accident prevention The safety regulations and accident prevention regulations are legally...

4 Prior to performing maintenance and repair tasks, turn off the engine and remove the key. Injuries due to fluid escaping under high pressure. Comply with the notice in the operating manual. 4.4.2 Machine-specific notice Machine-specific warning signs and instructions concerning operation and maintenance of the machine are explained in this section. Danger due to ejected parts when the engine is running – maintain a safety distance! Only touch machine parts after they have come to a complete standstill! Do not open or remove protective devices when the engine is running. During operation, maintain...

4 Implement is only suitable for a PTO shaft speed of 2000 rpm! Predominantly mid-mount, front, or independent engine PTO shafts. Implement is only suitable for a PTO shaft speed of 1000 rpm! Usually an independent engine PTO shaft. Implement is only suitable for clockwise PTO shaft rotation! (CW) Implement is only suitable for counterclockwise PTO shaft rotation! (CCW) The direction of rotation is always specified when viewing the end of the PTO shaft from the front (see Fig. 1 page 5). Do not operate the mower without discharge guard or suction port! After each use re-tighten all screws Lubricating...

4 Each time before starting to drive, ensure that all described safety notices and protective devices are completely present and functional. Do not operate the implement if safety notices or safety devices are missing or damaged. 4.5.1 Protective device on the machine Protective cover Universal joint shaft Protective cover Gearing stub (drive) Protective cover Universal joint shaft Fig. 3: Protective cover for gearbox