Operating Manual Snow Blower SBL - M 12-40 QH
21Pages

matev GmbH Nürnberger Str. 50 90579 Langenzenn, Germany T +49 9101 9087 -0 F +49 9101 9087 -20 info@matev.eu www.matev.eu Original Operating Manual Snow Blower SBL - M 12-40 QH – JD Quick Hitch SBL - M 12 – 40C SBL - M 14 – 40C Carefully read this manual all the way through before using the machine. Version 12/

About this operating manual About this operating manual Dear customer! Thank you for purchasing this snow blower, we appreciate your trust. Prior to using this implement for the first time, read this operating manual carefully and conscientiously all the way through. Keep this operating manual where it is easily accessible. This will enable you to refer to important information and handling instructions as needed. Listings with bullet points are marked as follows:  Text  Text  Text Handling instructions are marked in the sequence in which they should be executed, as follows: 1. 2. 3....

Safety Note Must be read!!! Guidelines and instructions with which you must comply, are summarized in this section. Personnel who install, operate and maintain the snow blower, must have read and understood this operating manual. Intended use  The implement is used exclusively in winter service for clearing snow on roads, lanes, walking paths, plazas, and industrial areas.  Any use extending beyond the intended use cited above is considered nonintended use. The manufacturer bears no liability whatsoever for resulting damage; the risk associated with non-intended use is borne solely by the...

General safetynotices In this section general safety notices are explained that are used in the subsequent sections. Comply with these safety notices to ensure safe operation and to save work time and costs.  In addition to the instructions in this operating manual, also comply with the generally valid safety and accident prevention regulations! Young persons under the age of 16 are not allowed to operate the implement!  Comply with the respective regulations for use on public traffic routes!  Prior to commencing work, become familiar with all features and activation elements, and their...

Special safety notices The safety instructions specified in this section are also affixed as stickers on the implements. Attention! Ensure that the engine PTO shaft is at a standstill. Only use cloths, water soap for cleaning. Do not use any solvents, diesel fuel or gasoline. Replace damaged signs. If the sign is on a component that must be replaced, you must ensure that a new sign is affixed on the spare part. - Carefully read the operating manual before commissioning the machine - Danger entanglement Danger of hand or arm injuries - Ensure that the complete machine is at standstill before...

Basic rules  Each time before starting up, check the machine for operational reliability!!!  Cleaning tasks, e.g. with a high-pressure cleaner, should be executed in such a manner that the water jet is not held directly on bearing parts and turned parts (shaft seals, lubricating nipples, etc.) Otherwise, check the moving parts for ease of movement, regrease if necessary!  Failure to comply with these instructions invalidates the guarantee claim. Task and use In conjunction with a tractor the snow blower is used to clear large quantities of snow off of roads, lanes, walking paths, plazas...

Installation Danger! Switch off the tractor and remove the ignition key before mounting or dismounting the implements. Note! Enter the vehicle chassis number of the snow blower in section 7.4 of this operating manual. The rear axle of the vehicle is offloaded depending on the weight of the equipment. To avoid loss of adhesion, the weight on the off-loaded axle must be at least 25% of the empty weight of the vehicle. If required, or if possible put on chains. Check the lift capacity and the stability, and if required, weight with ballast, to prevent the vehicle from tipping. In the movement...

Mount snow blower SBL - M 12-40 C and SBL - M 12-40 C on tractor Depending on tractor size and type and size of the coupling support, the attachment triangle on the snow blower is fastened with screws. The height of attachment must be selected depending on the tractor size. The attachment can also be shifted in length. Fig. 4: Attachment of the snow blower The connection between coupling support and attachment must be secured against uncoupling of the connection, depending on the design of the attachment. Possible securing options are:  Peg with bolts and secure with cotter pin  Fasten...

Installation of the universal joint shaft The transmission of force between tractor and snow blower occurs mechanically via a universal joint shaft. Depending on tractor type the supplied universal joint shaft may be too long. Execute the steps described below to shorten the universal joint shaft. Only use the universal joint shaft provided by the manufacturer. Attention! Damage can occur to the attached implement or on the tractor. Only use the provided universal joint shaft. Note! In addition, when mounting the joint shaft, comply with the instructions in  the original manual provided by...

Fig.9: Deburr the sawn edges Repeat steps described steps on the other half of the universal joint shaft. Deburr the sawn edges. Grease the profile tube. Fig. 10: Grease the profile tube. 10. Slide the profile tubes together. Mounting the universal joint shaft 1. 2. 3. 4. Press the locking disk that is on the outer side and keep it depressed. Slide the splined shaft onto the splined shaft of the PTO shaft. Release the lock disk. Slightly move the universal joint shaft back and forth until the locking disk audibly locks in place. Fig. 11: Allow the locking disk to lock in place 5. 6. Connect...

Working with the snow blower Attention! The vehicle behavior, steering and brake capacity are influenced through the attached equipment Attention! The snow blower can be damaged. Before each use, check to ensure proper adjustment of the support skids. Only operate the snow blower from the driver’s seat of the tractor. Attention! Third persons can be severely injured and objects can be damaged. Ensure for yourself that no objects are concealed under the snow. When operating the snow blower no one should be in a radius of 50 m around the machine, as a precaution against being caught by the...