Original Operating Manual SRM-FB 150

About this operating manual Dear customer! Dear customer! Thank you for purchasing this implement, we appreciate your trust. Prior to using this implement for the first time, read this operating manual carefully and conscientiously all the way through. Keep this operating manual where it is easily accessible. This will enable you to refer to important information and handling instructions as needed. Listings with bullet points are marked as follows:    Text Text Text . . . Handling instructions are marked in the sequence in which they should be executed, as follows: 1. 2. 3. Text Text Text...

Safety Guidelines and instructions with which you must comply, are summarized in this section. Personnel who mount, operate and maintain this implement, must have read and understood this operating manual. Intended use The snow blade is an implement for winter service and is used for clearing snow from roads, paths, and other areas. All other uses are excluded. Non-intended use causes:    Danger of injury to the operator or third parties Damage to the tractor and the implements Environmental damage Qualifications of personnel Only personnel 18 years of age or older, or instructed personnel...

Attention! Injuries can occur due to improper operation. The implement can be damaged. Read the operating manual all the way through. Comply with the safety instructions.  Attention! Danger of crushing due to moving parts. Never reach into the crushing hazard zone if parts are moving or can move. Comply with the notice in the operating manual. Special safety notices Safety instructions are specified in this section that are also affixed as stickers on the implement. Attention! Prior to start-up read and comply with the operating manual and the safety instructions. Attention! Prior to performing...

Installation Attention! Before starting up the implement, read the instructions on safety and handling for operation of the entire implement and connection to the tractor. Attaching the snow blade on the tractor In order to attach the snow blade on a tractor, the tractor must be equipped with a Quick Hitch front power system. The attachment is described in more detail below: 1. 2. Position the snow blade in such a manner that you can drive to just in front of the receptacle of the snow blade. Then the Quick Hitch is lowered all the way and is brought under the receptacle of the snow blade by...

Adjustments on the snow blade Before starting to clear snow, the skids must be correctly adjusted. To do this the snow blade is lowered onto a level surface via the hydraulics. The snow blade is correctly adjusted when the skids rest on the ground and the scraper bar just barely touches the ground or clears the ground by 1-2 mm. If this is not the case the snow blade must first be adjusted. To do this proceed as follows: 1. 2. 3. 4. 5. Lower the snow blade until it is just a little above the ground, and place it on an intermediate substrate that is 1-2 mm thick. Set the hydraulic system to the...

Operation and fault correction Operation and fault correction Operation If the snow blade is correctly adjusted, you can start working. For travel between implementation sites the snow blade is lifted above the front lift and the lowering safeguard of the front lift is activated. To work with the snow blade it must be lowered and the hydraulic system must be switched to float position. Danger! Driving on pressure is prohibited. This can make the vehicle unsteerable! Attention! A disabled hydraulic system can result in damage to the implement and/or tractor! To clear the snow to a specific side...

Operation and fault correction Contact person If there are faults, problems, or other indications of malfunction, contact your sales consultant or local dealer. Enter the article number and the chassis number here. This information is on the type plate of the implement.

Maintenance The entire implement must be subjected to regular service. After first use, the threaded unions on the snow blade must be checked and retightened if necessary. The screws of the scraper bar and the attachment flange are extremely important in this regard. Prior to each use, check the safety elements and moving parts for wear. Prior to each use, check the adjustment of the skids. Clean the implement after each use. Check the status of the snow blade, the level of wear on the scraper bar Maintenance after 25 operating hours (or after a longer standstill period): At regular intervals,...

Disposal The snow blade must be disposed of in accordance with the applicable regulations of the municipality or the country. Take the parts to the collection points for residual waste, special waste, or recycle them depending on material. matev GmbH does not provide any disposal services. Guarantee The general delivery conditions of matev GmbH apply. Technical data and accessories Dimensions Blade width Blade height

EC Declaration of Conformity for a machine to confirm compliance with the Machinery Directive 2006/42/EC and with the statutory regulations issued for the implementation of the Machinery Directive. matev GmbH Nürnberger Str. 50 90579 Langenzenn, Germany declares that the machine complies with the provisions of the Machinery Directive 2006/42/EC and with the implementing national statutory regulations. The signer is authorized to compile the technical documents. The address is the address of the manufacturer. Date / Signature Name of signer Signer information August 2017 Georg Hemmerlein Managing...