Original Operating Manual Snow blade SRM-FB 120 CD Angle adjustment mechanical

About this operating manual About this operating manual Dear customer! Thank you for purchasing this device, we appreciate your trust. Prior to using this device for the first time read this operating manual carefully and conscientiously all the way through. Keep this operating manual where it is easily accessible. This will enable you to refer to important information and handling instructions as needed. Listings with bullet points are marked as follows: · · · Text Text Text Handling instructions are marked in the sequence in which they should be executed, as follows: 1. 2. 3. Text Text Text...

Safety Guidelines and instructions with which you must comply are summarized in this section. Personnel who install, operate and maintain the device, must have read and understood this operating manual. Intended use The snow blade is an implement for winter service and is used for clearing snow from roads, paths, and other areas. All other uses are excluded. Non-intended use causes: · Health hazards for the operator or for third parties · Damage to the tractor and the attachments · Environmental damage Qualification of personnel Only personnel 18 years of age or older, or instructed personnel...

Special safety instructions Safety instructions are specified in this chapter that are also affixed as stickers on the implements Attention! Danger of injury due to moving parts. Remove the ignition key before performing maintenance tasks on the implement. Attention! Injuries can occur due to improper operation. The implement can be damaged. Read the operating manual all the way through. Comply with the safety instructions. Attention! Injuries due to fluid escaping under high pressure. Comply with the instructions in the operating manual. Attention! There is an increased risk of accident due...

Installation Danger! Severe injury to the operator or third parties occurs. Switch off the tractor and remove the ignition key. Preparatory measures The prerequisite for using the SRM-FB 120 CD snow blade is that the tractor must already be equipped with the matev (131 5974 or 131 7014) attachment bracket in conjunction with the (131 7015) lift-out linkage. Attachment bracket Lift-out linkage Fig. 1 Attachment bracket with lift-out linkage Attaching the snow blade 3.2.1. Fix the snow blade in place on the attachment bracket 1. Guide the connection tube of the snow blade into the connection tube...

Attaching the mechanical angle adjustment 1. The Mechanical angle adjustment can only be attached if an intermediate bracket (see Fig. 3) is already present or is also mounted. Spare part number: 06 001 957 Fig. 4 Attachment kit - mechanical angle adjustment Remote control rod, separable with handle and hand lever Holder for operating rod Ratch Holder for forked bolt Cable pull

Preparations on the snow blade: Attention! Danger of injury due to moving parts. Remove the ignition key before performing maintenance tasks on the implement. Drive the tractor into the workshop, switch off the motor and remove the ignition key. Remove the snow blade from the tractor. If the intermediate bracket is not like (Fig. 3): · Dismount the springs of the drive-over safeguard · Dismount the snow blade intermediate bracket (must be replaced with the intermediate bracket, see Fig. 3). Drill 2 fastening bores ø 8.5mm (Fig. 5) in the blade plate. Fig. 5 Bores (2x ø 8.5 mm) in the blade plate...

After preparing snow blade and tractor mount the attachment kit for the mechanical angle adjustment as shown in Fig. 7-10. Cable pull with clamp nuts Compression spring Intermediate bracket Clamp screw Fig. 7Attachment - intermediate bracket and ratch Fig. 8 Attachment - holder for operating rod Fig. 9 Operating rod with handle

Fig. 10 Attachment - holder for forked bolt Attachment of intermediate bracket and ratch on the snow blade Attachment of the holder for the operating rod on the running board Attachment of the operating lever with handle Fastening of the holder for forked bolt Guide the cable pull through the receptacle sheet metal, compression spring and ratch Fasten the cable pull (clamp nuts) and clamps of the steel cable (to tension) with clamp screw (stub screw in ratch) Lift function The snow blade can be lifted mechanically (foot activation) or hydraulically depending on the tractor type. Lift-out linkage...

Swing function The snow blade has a manual (peg bolt) or mechanical angle adjustment element. The snow blade must be swung in lifted status (mechanical or hydraulic). Swing via manual adjustment For the manual angle adjustment you must pull off the peg bolt and reinsert it in the desired angle position of the snow blade. Swing via mechanical angle adjustment Use the mechanical angle adjustment to conveniently swing the snow blade from the driver's seat. To do this the attached hand lever of the operating rod must be pressed and the operating rod must be pushed at the same time (swing in direction...

Adjustments on the snow blade: Before starting to clear snow, the slide runners must be correctly adjusted. To do this the snow blade is lowered onto a level surface. The snow blade is correctly adjusted when the steel skids rest on the ground and the scraper bars just barely touch the ground or clear the ground by 1-2 mm. If this is not the case the snow blade must first be adjusted. To do this proceed as follows: 1. Lower the snow blade until it is just a little above the ground, and place it on an intermediate layer that is 1-2 mm thick. Disable the hydraulic system and switch off the tractor....

Clamp screw Steel skid Attention! The tractor and the environment can be damaged. Only use the supplied material. Attention! Danger of crushing due to moving parts. Never reach into the crushing hazard danger zone if parts are moving or can move. 1. Connect the snow blade on the attachment bracket. 2. Start the tractor and move the connected implement up and down. Swing the implement to the left and to the right. Ensure that all threaded unions are firmly connected and that there is no danger of collision with adjacent components.