guide-manual-mirafeed-spreader
16Pages

TECHNICAL AND MAINTENANCE MANUAL SPREADER USER INSTRUCTION

1. INTRODUCTION This booklet describes the user and maintenance instructions for Spreader. The user is expected to read carefully the entire manual and to ensure that all information in it is fully understood. ACQUA&CO shall not accept any direct and indirect liability resulting from negligence and failure to comply with the rules described in this booklet. Moreover, it shall not be liable for any damage caused to people, animals or things by an incorrect installation and/or improper use of the equipment. When purchasing the equipment, make sure that it is complete and intact. Any...

1.3 SCOPO E USO PREVISTO / CAMPO DI APPLICAZIONE The spreader is a Mirafeed accessory that allows to spread the feed (powder or pellet) in the water surface of the tank. It is fixed to the Mirafeed in a specific position that permit the feed to fall down on the spreader high velocity propeller. The propeller will strike the feed and throw it in the desired direction. The spreader must be connected to 24 V AC in the control box together with the Mirafeed. This connection allow you to sincronize the two motors. NOT continuous operation: it is cyclically timed at least every hour. This...

Before starting to work, make sure that the machine is perfectly intact. Any part that is found defective, damaged or broken must be repaired or replaced by qualified and authorised personnel. Repairing or having parts repaired by staff that is not authorised by the Manufacturing Company will void the warranty and make equipment unsafe and potentially dangerous. If the spreader is accidentally dropped, check its integrity. Any type of check, control, cleaning, maintenance, changeover and replacement of parts must be carried out after shutting down the machine and isolating its connections....

2.6 SHEARING RISK - RESIDUAL RISK The machine is accessible for maintenance purposes. A propeller is constantly rotating at high velocity to spread and dispense the feed. No protection is provided, otherwise the machine cannot work properly. DO NOT PUT YOUR FINGERS AND HANDS ON THE PROPELLER DURING WHILE THE MACHINE IS WORKING DO NOT PLACE ANYTHING ON THE PROPELLER OTHER THAN FEED OR OTHER SUBSTANCES FOR WHICH IT HAS BEEN DESIGNED AND SOLD. IT IS STRICTLY PROHIBITED TO WORK ON THE FEEDER WHEN THE MACHINE IS V V OPERATING. 3. DESCRIPTION

4. TRANSPORT AND STORAGE. The Spreader device is delivered with its power supply cable and electrical box inside cardboard boxes suitable for transport and storage. In case of storage, it is recommended to avoid placing heavy material onto the machine to prevent any crushing or damage 4.1 UNPACKING / PRELIMINARY INSPECTION Upon receipt, make sure that the delivered goods match those ordered. Ensure that the goods show no damage caused by transport. Any damage detected upon receipt must be documented and notified to the sender within 8 (eight) days from arrival. The cardboard packaging, if...

4.3 MOUNTING ON THE FEEDER Fix the spreader on the feeder by screw (13) and washer (12) to the round bar (2) Now the spreader and the feeder are locking on the support Unscrew the screw (11). Remove the propeller (4- 5). Reassemble the propeller with the screw (11).

4.5 FRONTAL AND CIRCULAR SPREADING ADJUSTMENT The spreader can spread the feed in frontal direction or in circular direction covering 360°, depending on the application, with simple adjustments. To position the spreader propeller in frontal or circular direction you need to unscrew the knob n.11; now the plate n.1 is free to move back and forth and to rotate. Adjust the position of the propeller to the desired one then screw the knob n.11 to fix the position. Note: Suggested position can be changed according to application and type of feed. Frontal spreading Circular spreading

remove the srew (11) and propeller (4-5) Extract the motor protechion (3). Extract Motor (3) and the gasket (15) Perform all the previous steps contrariwise for the re-assembly 4.7 ELECTRICAL CONNECTION AND COMMISSIONING NOTE: THE ELECTRICAL CONNECTION OF THE MACHINE MUST BE CARRIED OUT BY SPECIALISED PERSONNEL. IT IS UP TO THE INSTALLER TO PERFORM THE CONNECTIONS IN COMPLIANCE WITH LEGISLATION IN FORCE IN THE COUNTRY OF INSTALLATION. - Make sure that the mains voltage and frequency match the data stated on the motor plate. - Bring a power supply cable compatible with power consumption...

- The spreader is provide with an electric box - Connect the Wire (1) to the electric board to the 24V AC. - Connect the Wire (2) of the feeder in the box (PICT. 1). 2 –Wire from feeder 24V AC → 24V AC 24V AC → 24V DC

RESIDUAL RISK: the sudden re-start of the machine can be a source of danger for operators working nearby it. The spreader contains an high speed propeller: - NEVER PUT YOUR FINGERS, HANDS, HAIR, CLOTHES OR ANY OTHER OBJECT IN THE TANK OR NEAR THE DISC WHEN THE MOTOR IS RUNNING. NEVER PLACE ANYTHING OTHER THAN FEED INTO THE TANK AND NEAR THE DISC WHEN THE MOTOR IS RUNNING. 4.8 REGULAR CHECK Before carrying out checks make sure that voltage is disconnected and that unintentional connections are not possible. It is recommended to regularly check: - The conditions of cables and cable guides -...

5.3 MACHINE SCRAPPING - If you decide not to use the machine anymore, it is recommended to make it inoperative by removing the electrical power supply cable. - Always keep it outside the reach of children. - Since the machine is a special waste, it must be disassembled and the parts of the same material collected for disposal in compliance with legislation in force. - Do not use any scrapped items as spare parts. INFORMATION FOR USERS In compliance with Directives 2002/95/EC, 2002/96/EC and 2003/108/EC on the restriction of the use of certain hazardous substances in electrical and...

DECLARATION OF CONFORMITY within the meaning of Art. 4 Par. 2 of Directive 2006/42/EC The Legal Representative of the Company ACQUA&CO with registered office in Via Augera 5/a, CadelboscoSopra (RE) Italy declares on its own sole responsibility that the produc: SPREADER Complies with the requirements of the EEC Directive(s): 2006/42/EC Machinery Directive, 2006/95/EC, Low Voltage Directive, It is prohibited to commission the machine under this declaration before the system of which it will be part, together with the control panel and all necessary (mechanical and electrical)...