AUTO TRANSFER SWITCH & MAINS CONTROL MODULE EXPANSION DEVICES • DSE2130 Input Expansion Module • DSE2131 Ratio-metric Input Expansion Module • DSE2133 RTD & Thermo-couple Expansion Module • DSE2152 Ratio-metric Output Expansion Module • DSE2157 Output Expansion Module CONTINUOUS VOLTAGE RATING CRANKING DROPOUTS Able to survive 0 V for 100 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT MAXIMUM STANDBY CURRENT MAINS (UTILITY) & BUS VOLTAGE RANGE Frequency RANGE Negative switching • Mains (utility) failure detection • Mains (utility) power monitoring (kW, kV Ar, kV A and pf) • Comprehensive synchronising and loadsharing capabilities • Peak lopping & shaving functionality • Mains (utility) kW export protection • Mains (utility) de-coupling protection • Advanced integral PLC editor • User configurable RS232, RS485 & Ethernet communications • User configurable MODBUS pages • Advanced SMS control and fault messaging (addition GSM modem required) • DSENet expansion compatible • Data logging and trending • 4-Line back-lit LCD text display • Multiple display languages • Five key menu navigation • Front panel editing with PIN protection • Customisable status screens • Configurable timers and alarms • Multiple entry scheduler • Easy access diagnostic pages • Backed up real time clock • Fully configurable via DSE Configuration Suite PC Software • Power modes for when in parallel with the mains • Redundant MSC communication wired to CAN ports • True manual breaker control when in manual mode • Native no bus breaker support for signal ATS applications • Separate ramp up and ramp down rates configurable via PLC • In-built SNMP • Configurable CAN transmit & receive • Battery Chargers on DSENet® • Two part solution allows upto 1.2 km between mains (utility) & • 132 x 64 pixel ratio display for clarity • Real-time clock provides accurate event logging • Ethernet communication provided builit in advanced remote monitoring. • Can be integrated into building management systems (BMS) and programmable logic control (PLC) • Increased input and output expansion capability via DSENet® • IP65 rating (with supplied gasket) offers increased resistance to water ingress • Advanced Internal PLC editor allows user configurable functions to meet specific application requirements. PANEL CUT-OUT MAXIMUM PANEL THICKNESS OPERATING TEMPERATURE RANGE STORAGE TEMPERATURE RANGE RELATED MATERIALSTITLE PART NO. DSE8660 MKII Installation Instructions 053-184 DSE8660 MKII Operator Manual 057-259 DSE8660 MKII PC Configuration Suite Manual 057-257 DSE8610 MKII Data Sheet 055-204 Highfield House, Hunmanby Industrial Estate, Hunmanby YO14 0PH TELEPHONE +44 (0) 1723 890099 FACSIMILE +44 (0) 1723 893303 EMAIL [email protected] WEBSITE www.deepseaplc.com 3230 Williams Avenue, Rockford, IL 61101-2668 USA TELEPHONE +1 (815) 316 8706 FACSIMILE +1 (815) 316 8708 EMAIL [email protected] WEBSITE www.deepseausa.com Deep Sea Electronics Plc maintains a policy of continuous development and reserves the right to change the details shown on this data sheet without prior notice. The contents are intended for guidance only. Registered in England & Wales No.01319649 VAT No.316923457

ENVIRONMENTAL TESTING STANDARDS ELECTRO MAGNETIC COMPATIBILITY EMC Generic Immunity Standard for the Industrial Environment BS EN 61000-6-4 EMC Generic Emission Standard for the Industrial Environment DSE8660 MKII AUTO TRANSFER SWITCH & MAINS CONTROL MODULE The DSE8660 MKII is an easy-to-use single or multi-mains controller with automatic transfer switch capability. Designed to synchronise single or multiple DSE8610 MKIIs and DSE8680 MKII with single or multiple mains (utility) supplies, the DSE8660 MKII will automatically control the change over from mains (utility) to generator supply or run...