FSP-2X1 SERIES
1 / 7Pages

HIGH/LOW/OFF PIR FIXTURE INTEGRATED OUTDOOR PHOTO/MOTION SENSOR FSP-2X1 SERIES MODELS FSP-201, 12–32VDC Use with dim-to-off driver or ballast or with Wattstopper power pack FSP-211, 120/277VAC, 230–240VAC (single phase), 50/60Hz FSP-221, 100–347VAC (single phase) or 208/230/480VAC (phase-to-phase) SPECIFICATIONS & FEATURES Load Ratings (FSP-211, FSP-221): @ 120V 0–800W tungsten, ballast, LED driver; 1/6hp motor @ 230–240V 0–300W ballast, LED driver @ 277V 0–1200W ballast, LED driver; 1/6hp motor @ 347/480V 0–1200W ballast, LED driver, 1/6hp motor (FSP-221 only) Current consumption (FSP-201): Normal Operation: 15mA IR Programming: 45mA 0-10V sinking current: 50mA PRODUCT OVERVIEW The FSP-2x1 series are passive infrared (PIR) outdoor sensors that raise or lower the electric lighting level to high, low or off based on motion and/ or daylight contribution. Typically, once the sensor stops detecting movement and the time delay elapses, lights will first fade to low mode, and eventually switch off. When motion is detected, the sensor ramps the light level to high mode unless the daylight contribution is sufficient. The integral photocell can also switch the lights on and off for dusk to dawn control so that lighting remains on overnight even without motion detection. These slim, low-profile sensors are designed for installation inside the bottom of a light fixture body and is UL listed for use in wet and cold locations. Initial setup and subsequent sensor adjustments are made using a wireless handheld configuration tool (FSIR-100). This tool enables adjustment of sensor parameters including high/low mode, sensitivity, time delay, cut off and more. The FSIR-100 can read current parameter settings and stores up to six sensor parameter profiles to speed commissioning of multiple sensors. Light Sensor IR Transmitter Three interchangeable lenses for mounting between 8’ and 40’ Remote setup and adjustment with handheld wireless configuration tool Adjustable high and low modes (high: 0 to 10V, low: off, 0 to 9.8V) Adjustable time delay (30 seconds, 5 to 30 minutes) Adjustable cut off delay (none, 1 to 59 minutes, 1 to 5 hours) Adjustable sensitivity (low, med, max) Adjustable setpoints: hold off setpoint (none, 1 to 250 fc, auto); photocell on/off setpoint (1 to 250 fc) Adjustable ramp and fade times (1 to 60 seconds) Lead length (FSP-221): 36” (91.44cm) Operating temperature: -40°F to +167°F (-40°C to +75°C) Weight: FSP-201, 2.1 oz (59 g); FSP-211 2.8 oz (80 g), FSP-221, 5.5 oz (155 g) UL and cUL listed; CE; TUV listed IP66 rated FSIR-100 is FCC Part 15 compliant Five year warranty MATERIALS Polycarbonate, flame retardant, UV resistant, impact resistant, recyclable Meets materials restrictions of RoHS *PEP designation applies to FSP-211 only NOTE: Remove Cap before use 1

FIXTURE SENSORS & CONTROLS FSP-L2 top and side coverage patterns FSP-L3 top and side coverage patterns FSP-L7 top and side coverage patterns WWW.LEGRAND.US/WAT TSTOPPER

FIXTURE SENSORS & CONTROLS DIMENSIONS OF LENS OPTIONS 2.33" 59.2mm FSP‑L2-S, FSP-L3-S, and FSP-L7-S Dimensions The FSP-Lx-S models include a shroud, which blocks high-angle light coming from the fixture, to improve photocell performance. With the shroud attached, the dimensions for all three lenses are identical FSP-L2-S and FSP-L3-S INSTALLING THE FSP-2X1 SENSOR IN LIGHT FIXTURE 1. Determine an appropriate mounting location inside the light fixture. Allow a minimum distance of 0.2” (5.1mm) from the end of the sensor to the wall of the fixture. 2. Drill a 1.31” (33.3mm) diameter hole...

FIXTURE SENSORS & CONTROLS Tightening Nut Lens Assembly Inside Fixture Wall Rubber Gasket Outside Fixture Wall Tightening Nut (or Optional Collar) Tightening Nut (or Optional Collar) Rubber Gasket Fixture Wall Lens Assembly Inside Fixture Wall Tightening Nut (or Optional Collar) Rubber Gasket Outside Fixture Wall Tightening Nut (or Optional Collar) Rubber Gasket Fixture Wall Lens Assembly FSP-221 NOTE: The outside fixture wall thickness should be no greater than 0.125” (3.18mm) for optimal sensor mounting and security. SEQUENCE OF OPERATION 1. Dimming: When motion is detected within the...

FIXTURE SENSORS & CONTROLS ADJUSTABLE CONTROL PARAMETERS Power On/Off The FSIR-100 is a convenient handheld remote tool for setting up the FSP-2x1. Adjustable settings can be changed as needed for specific applications. Sensor Configuration New Setting Current Settings Test Mode Recall Profiles Home/Main Menu Up Right/Next Back Left Down 1. High Mode: When the sensor detects motion the dimming control output ramps up to the selected HIGH light level (default is 10V). 2. Low Mode: After the sensor stops detecting motion and the time delay expires the dimming control output fades down to the...

FIXTURE SENSORS & CONTROLS WIRING DIAGRAMS Ground Dimming Ballast/Driver Dim-to-Off Ballast/Driver +VDC Output (Red) Ground (Green) Ground (Green) Power Pack Lighting Load Black Green Class 2 Output 24 VDC, 225 mA UL 2043 Plenum Rated COM/GND (Black) wiring only 0-10V – (Pink) CTRL (Blue) DIM+ (purple) High/Low PIR Occupancy Sensor 12-32 VDC, 15mA 18-20 AWG Solid CU Wire Only High/Low PIR Occupancy Sensor 12-32 VDC, 15mA 18-20 AWG Solid CU Wire Only 14-18 AWG Solid CU Wire Only 14-18 AWG Solid CU Wire Only FSP-201 typical wiring with dim-to-off ballast or LED driver with auxiliary output....

ORDERING INFORMATION Master Pack Details Inner Pack Details Master Case dimensions (inches) Pack Quantity Length Width Height Weight (pounds) Inner Case dimensions (inches) Pack Height Quantity Length Width Weight (pounds) Fixture mount, passive infrared motion sensor, low voltage Fixture mount, passive infrared motion sensor Fixture mount, passive infrared motion sensor, BAA/TAA compliant* Fixture mount PIR sensor, extended voltage Remote Handheld Configuration Tool Three standard 1.5 AAA alkaline batteries (included) 360° lens, maximum coverage 48’ diameter from 8’ height 360° lens,...