Standard and ancillary equipment HKD402
3Pages

Price List a g r o l i n e r Three-axle three-way tipper trailer Type: HKD 402 24 tonne permissible total weight Standard equipment: Tyres: Axles: Springs: Steering: Chassis frame: Brake system: Tipping system: Tipper frame: Bulkhead: Side panels: Electrical system: Technical data: Cargo area dimensions: 6 x 385/65R22.5 factory refurbished tyres on centre well rims, approved for 80 km/h tapered roller bearing axle, 3 x 9.0 tonnes axle load approved up to 105 km/h (without ABS, up to 60 km/h), 2040 mm track, wheel brake 420 x 180 mm, equipped with ABS and automatic boom adjuster (AGS) parabolically suspended linked steering unit with dynamic brake compensation on the double axle approved up to 105 km/h; overload protection for the rear parabolic spring suspension Turntable steering with ball rim and type-tested triangular drawbar, height adjustable as well as drawbar relief steel welded construction, double T main load bearer, double T cranked to the front dual line service brake system with automatic load-dependent brake force control (ALB), 6 x diaphragm brake cylinder, spindle parking brake for the rear axle 3-way tipper; hydraulic multi-piston press with cardanic suspension, 1 line system, ball tipper bearings with retainer at the rear, 2 unmistakable locking pins, hydraulic stroke limiter, safety rope profile steel in welded construction, 4 mm steel floor plate fixed made from webbed combined multiplex board 18 mm, WBP pasted, in the area of the side panels the use of stainless steel VA bolts, fixed corner stanchions, steps on the drawbar, ergonomic access ladder with platform and accident protection bar according to the German accident prevention regulations (UVV), on the inside of the bulkhead webbed combined multiplex board as with the bulkhead embedded in aluminium profile (with integrated water drain) with robust rubber seals that can be replaced, 3 side panels each without horizontal partitioning, fixed middle stanchions with 2 removable connecting tubes each, split, central bottom unlocking, bottom unlocking lever at the front and rear with top dead point tensioner, optimally designed for the equipping of an automatic side panel remote unlocking system basic design is the same as the side panels with an 1 grain hatch in the middle (480 x 290 mm) with lever operation (left side) and removable discharge chute, fixed corner stanchions, central bottom, bottom unlocking lever at the left with top dead point tensioner 12 Volt system according to the guidelines of the StVZO (German traffic laws) with 7-pin connecting cable, triangular reflector and yellow side reflectors, three unit lamps (rubber mounted), number plate lights, position lights stable underride protection according to EC Directives, number plate bracket, 2 x wheel chocks with bracket, protective caps on the screw connections, resting point supports for reducing the noise during driving operation, plastic mudguard on the front axle and rear axle, park sockets for all connections on the drawbar vehicle blasted with steel grit and also degreased, chip-resistant primer, sealing of areas in particular risk of corrosion using bodywork sealing compound, Dual-component corrosion protection paint, top coat in German quality dual-component gloss paint Superstructure: Kroger green, panels = covered with "green" film on both sides, not UV resistant Permissible total weight: 24,000 kg Empty weight approx. 6,400 kg (in the basic equipment) Platform height approx. 1,420 mm Oil requirement: approx. 39.9 litres Panel width also between the middle and corner stanchions! (Technical changes reserved)

Basic price a g r o l i n e r Type: HKD402 Ancillary equipment subject to charge: A SUPERSTRUCTURE A 0504 LIGHT version, weight-optimised version Weight saving of up to 250 kg (depending on the equipment) Floor plate 3 mm instead of 4 mm. No loss in stability by using high-tensile special steels. A 0604 Side panels with plastic lightweight panels, 20 mm thick, side panel height 1500 mm, (colour white or in combination with L 1204, not suitable for direct filling by woodchippers), A 0624 Side panels with plastic lightweight panels, 20 mm thick, side panel height 1700 mm, (colour white or in...

F 4954 Voltage converter for light systems from 12 Volt to 24 Volt permanently mounted on the chassis F 5004 24 Volt lighting system F 5010 Power supply for light system 15 pin instead of 2 x 7 pin F 5104 Side marking lights (LED) F 5144 Contour marking film, yellow on the side and rear of the vehicle (mandatory for approval > 60 km/h) F 5164 Position and number plate lights as LED version (24 Volt light system required) F 5200 5-unit rear lights with fog light and reversing light (second 7-pin 24 Volt connection required) F 5204 5-unit rear lights LED version with fog light and reversing...