Please read carefully before using the machine. Keep for future reference. This instruction manual/assembly instruction is to be considered as part of the machine. Suppliers of new and second-hand machines are required to document in writing that the instruction manual/assembly instruction was delivered with the machine and handed over to the customer. INSTRUCTION MANUAL Version 3.21.00 Original instructions

Preface Dear Customer, By purchasing the machine control unit AXIS EMC ISOBUS for the AXIS EMC mineral fertiliser spreader, you have shown confidence in our product. Thank you very much! We would like to justify the trust that you have placed in us. You have purchased a powerful and reliable machine control unit. If any unexpected problems should occur: Our customer service will always be there for you. We ask that you carefully read through and adhere to this operating manual and the operating manual of the machine before putting it into operation. This manual may also describe equipment that...

User instructions About this operating manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Significance of warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Instructions and procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Listings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Operation AXIS EMC ISOBUS 4.1 4.2 4.3 4.4 Activating the machine control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Navigation within the menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Fertiliser settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4.4.1 Application rate . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Spreading operation with the machine control unit AXIS EMC ISOBUS 5.1 5.2 5.3 5.4 5.5 Calling up the remaining quantity during spreading (weighing spreader only) . . . . Refilling (weighing spreader only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote-controlled limited border spreading unit TELIMAT with AXIS-M 30.2 . . . . Electrical TELIMAT setting with the AXIS-M 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . Working with sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5.1 Displaying the...

User instructions User instructions About this operating manual This operator's manual is an integral part of the machine control unit. The operator's manual contains important instructions for safe, proper and economic use and maintenance of the machine control unit. Compliance with its stipulations helps to avoid risks, reduce repair costs and downtime and to increase the reliability and service life of the machine controlled with it. The operator's manual must be kept in an easily accessible location close to where the machine control unit is used (e. g. on the tractor). The operator's manual...

User instructions Warning severity level The degree of danger is indicated by the signal word. The levels are classified as follows: n DANGER Type and source of danger This warning warns of a danger posing an immediate threat to the health and life of persons. Ignoring these warnings will result in very serious or even fatal injury.  Always observe the measures described to prevent this danger. n WARNING Type and source of danger This warning warns of a possible dangerous situation for the health of persons. Ignoring these warnings will result in very serious injury.  Always observe the measures...

User instructions Instructions and procedures Steps that the operator must carry out are shown as a numbered list. 1. Instruction for action step 1 2. Instruction for action step 2 Instructions involving only one step are not numbered. The same applies for action steps that do not have a specific sequence. A bullet is placed in front of these instructions:  Handling instruction Listings Listings without a specific sequence are shown with bullet points (level 1) and dashes (level 2):  References References to other text passages in the document are indicated with section number, headline text...

User instructions

NOTICE Due to the great variety of different ISOBUS-compatible terminals, this chapter is restricted to the functions of the electronic machine control system without indicating a specific ISOBUS terminal.  Please observe the instructions on the operation of your ISOBUS terminal in the corresponding operator's manual. Overview of supported AXIS fertiliser spreaders  Spreading depending on forward speed Electrical drop point adjustment AXIS-M 30.2/50.2 EMC (+W) Drive shaft speed AXIS-H 30.2/50.2 EMC (+W): Spreading disc speed EMC mass flow control

Display The display shows the current status information as well as the selection and input options for the electronic machine control unit. The most important information concerning the operation of the mineral fertiliser spreader is displayed in the operating screen. Operating screen description NOTICE The exact representation of the operating screen depends on the actual settings selected and on the machine type.

Machine control unit display Current application rate from the fertiliser settings or the task controller Button: direct entry of the application rate [2] Fertiliser information display (fertiliser name, working width and spreading disc type) Button: Adjustment in the fertiliser chart [3] Metering slide position, right/left [4] Drop point position, right/left [5] Quantity change, right/left [6] Spreading disc speed, right/left [7] Metering slide opening status, right/left [8] Function keys [9] Freely definable display fields [10] Mineral fertiliser spreader display [11] Selected operating mode...