AXIS-H ISOBUS
106Pages

Please read carefully before using the machine. Keep for future reference. This instruction manual/assembly instruction is to be considered as part of the machine. Suppliers of new and second-hand machines are required to document in writing that the instruction manual/assembly instruction was delivered with the machine and handed over to the customer. AXIS-H ISOBUS INSTRUCTION MANUAL Original instruction manual

Preface Dear Customer By purchasing the control unit AXIS-H ISOBUS for the mineral fertiliser spreader AXIS-H EMC, you have shown confidence in our product. Thank you very much! We want to justify this confidence. You have purchased a powerful and reliable control unit. If contrary to expectations any problems occur: our customer service is always there for you. Please read this operating manual as well as the operating manual of the machine carefully before commissioning and follow the advice given. This manual may also describe equipment that is not included in your control unit. Please...

User instructions About this operating manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Information on the illustration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.1 Significance of warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.2 Instructions and procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.3 Listings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.4...

Activating the machine control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Navigation within the menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Fertiliser settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 4.4.1 Application rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Spreading with the machine control unit AXIS-H ISOBUS 5.1 5.2 5.3 Monitoring the remaining quantity during spreading (weighing spreaders only) . . . 71 Refilling (weighing spreader only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Working with sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 5.3.1 Displaying the spreading type in the operating screen . . . . . . . . . . . . . . . . 73 5.3.2 Spreading with reduced sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 5.3.3...

User instructions User instructions About this operating manual This operating manual is an Integral part of the machine control unit. The manual contains important instructions for safe, proper and economic use and maintenance of the machine control unit. Compliance with its stipulations helps to Avoid risks, reduce maintenance costs and downtime and to increase the machine's reliability and service life. The operating manual is part of the machine. The complete documentation must be kept in an easily accessible location close to where the machine control unit is used (e.g. on the...

User instructions Warning severity level The degree of danger is indicated by the signal word. The levels are classified as follows: n DANGER Type and source of danger This warning warns of a danger posing an immediate threat to the health and life of persons. Ignoring these warnings will result in very serious or even fatal injury.  Always observe the measures described to prevent this danger. n WARNING Type and source of danger This warning warns of a possible dangerous situation for the health of persons. Ignoring these warnings will result in very serious injury.  Always observe the...

Instructions and procedures Steps that the operator must carry out are shown as a numbered list. 1. Instruction for action step 1 2. Instruction for action step 2 Instructions involving only one step are not numbered. The same applies for action steps that do not have a specific sequence. A bullet is placed in front of these instructions:  Handling instruction Listings Listings without a specific sequence are shown with bullet points (level 1) and dashes (level 2):  References References to other text passages in the document are indicated with section number, headline text and page...

User instructions

NOTICE Due to the great variety of different ISOBUS-compatible terminals, the present chapter is restricted to the layout and the functions of the CCI 100 ISOBUS terminal as example.  Please observe the instructions in the respective operating manual of your ISOBUS terminal. Overview of supported AXIS fertiliser spreaders Fertiliser spreader type Spreading operations depending on the forward speed Weigh cells Electrical drop point setting

Operating panel Including foil buttons, display, scroll wheel and stop switch. USB port with cover Protects the USB port from dirt. For data exchange, task controller and terminal updates. Mounting bracket For mounting the terminal within the tractor cabin. Terminal strip Terminal strip for the cables of the ISOBUS system. Softkey switch Enables switching the functions from the left to the right side of the screen.

Overview The CCI 100 machine control unit is operated with the following control elements:  18 foil buttons (6 firmly defined, 12 freely assignable foil buttons). Scroll wheel Stop switch Softkey switch NOTICE For further information on operating the CCI 100 terminal and its control elements, refer to the enclosed operating manual. The operating manual is an integral part of the terminal unit. Operating panel on the front side of the un

Scroll wheel Navigation through the menus and input fields and to acknowledge entries. Function keys 12 keys with variable functionalities, depending on the menu screen. Acknowledgement of error messages. Freely assignable key. Refer to the CCI 100 terminal operating manual. Navigation between the system screens of the terminal. Changing to the main menu of the terminal (refer to the manufacturer operating manual). Switching the terminal on/off. Stop switch The stop switch puts the connected devices into a safe state. Not all ISOBUS terminals support the stop switch. Page 10 Direct...