FM Series Specifications SPECIFICATIONS Tractor horsepower, maximum Tractor PTO Lift capacity Adjustability Nominal lift range Weight 250 HP (184 kw) SDX-117 & RDX-117 1000 RPM only, SDX-102, RDX-102 & SDX-840 540 RPM or 1000 RPM 5000 lbs (2268 kg) Accommodates tractors between 151” (3.8 m) and 211” (5.35 m) measured from front mount plate to drawbar pin 13”(33 cm) 3”(7.6 cm) higher without drive train depending on tractor installation 18” (45.7cm) 1650 lbs (748kg) with drive train, 1250lbs (567kg) without drive train Tractor horsepower, minimum Tractor horsepower, maximum Tractor Hydraulic Requirement 55 HP (41 kw) for SDX-840, 85 HP (63kw) for SDX-102, RDX-102 115 HP (86 kw) 3 remote circuits with a minimum total hydraulic output of 10 GPM at 1200 PSI. An additional circuit is required if the snow blower has a rotating drum. 540 RPM 5000 lbs (2268 kg) Fits tractors between 111.5” (2.8m) & 164.5” (4.2m) from front mount plate to drawbar pin 10”(25 cm) depending on tractor installation 3”(7.6 cm) higher without drive train depending on tractor installation 18” (45.7cm) 1400 lbs (636kg) Nominal ground clearance Tractor PTO Lift capacity Adjustability Nominal ground clearance Nominal lift range Weight Front Mount 3pt Hitch Frame Quick Attach Frame for Snow Blowers and SV Blades Enjoy the convenience, comfort and improved performance of a front mounted snow blower. - Front Mount & PTO Power - FM-350 - - Front Mount Mount & PTO Power - FM-115 - - Draw Bar Mount With Optional PTO Power - No matter how much snow you need to move you will appreciate the FM-350 and FM-115. The Front Mount Frames give you - Draw Bar Mount Without PTO Power - the ability to mount your 3pt snow blower or SV Plow on the front of your tractor instead of on the tractor's rear 3pt hitch. The FM-350 and FM-115 offer you better visibility and ergonomics when coupled with a Schulte Snow Blower. Blowing snow while driving forward, is more efficient than blowing snow in reverse. The FM-350 and FM-115 allow you an increased selection of travel speeds, as your tractor has many more forward gears then reverse gears. This increased gearing selection will result in better snow blowing performance and less wear and tear on the tractor clutch, and your neck. Schulte Industries Ltd. P Box 70, Englefeld, Saskatchewan, Canada S0K 1N0 .O. Tel: (306) 287-3715 Fax: (306) 287-3355 E-Mail: [email protected] Visit our Web site at: www.schulte.ca PRINTED IN CANADA PREPARED by NELSON GRAPHIC DESIGN Schulte is a registered trademark of Alamo Group Inc. Schulte Industries Ltd. reserves the right to change the design, specification of it’s products without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment.

The Schulte FM-350 and FM-115 are designed for simple and quick tractor mounting and removal. Once mounted to the tractor all pushing force is transmitted to the snow blower through the tractor drawbar. Tension screws at the rear drawbar ensure that the tractor sees only vertical load at the frame mounting points. - Rear Hitch or Optional Drivetrain - FM-350 - -- Rear Hitch or Optional Drivetrain - FM-115 - The FM-350 and FM-115 are a perfect match for Schulte model SDX or RDX snow blowers and the SV-10, SV-12 and SV-14 Folding V Plows. The drive line is capable of transferring 250 HP to the...