Operator’s Manual
30Pages

Operator’s Manual

The operators manual uses the following text formatting schemes to call attention to information related to simplifying system operation and proper operating practices to prevent accidental data loss. If in doubt about the results of performing an action or deleting an item from the system, back up all system files to the UsB external drive prior to proceeding with the action. DANGER: Indicates an immediate hazardous situation that, if not avoided, will result in death or serious injury. CAUTION: Indicates specific instructions to avoid accidental loss of data, system configurations...

RECOGNIZE SAFETY INFORMATION • This is a safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. • Follow recommended precautions and safe operating practices. FOLLOW SAFETY INSTRUCTIONS • Carefully read all safety messages in this manual and on your machine safety signs. Keep safety signs in good condition. Replace missing or damaged safety signs. Be sure new equipment components and repair parts include the current safety signs. Replacement safety signs are available from your dealer. • Learn how to operate the...

DIG SAFELY CALL (888) 258-0808 BEFORE YOU DIG! • Before digging, check location of cables, gas lines, and water mains. • Do not leave the operator's seat if any part of the plow contacts cables. AVOID POWER LINES CALL (888) 258-0808 BEFORE YOU DIG! • Running the tile plow through gas, electric, or water lines can cause serious injury or death to you or others. Always contact local utility companies to mark off gas, electric and water lines prior to tiling a field. • Locate Pipes And Cables Before Tiling. REMOVE PAINT BEFORE WELDING OR HEATING • Avoid potentially toxic fumes and dust. •...

STORE ATTACHMENTS SAFELY • Stored attachments can fall and cause serious injury or death. • Securely store attachments to prevent falling. Keep playing children and bystanders away from storage area. AVOID HIGH-PRESSURE FLUIDS • Escaping fluid under pressure can penetrate the skin causing serious injury. • Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. • Search for leaks with a piece of cardboard. Protect hands and body from high pressure fluids. • If an accident occurs, see a doctor immediately. Any...

Use a Signal Person • Use a signal person to direct movement of the tractor/fertilizer cart combination, whenever the tractor operator's view is obstructed. • Designate one individual as THE signal person. Always have signal person stand in clear view. Be sure signal person stays a safe distance away from the machine when it is moving. • Prior to starting the tractor, discuss hand signals and what each signal means to avoid misunderstandings and confusion which could result in a serious injury or fatal accident for someone. • Keep all bystanders away whenever the machine is moved. Pull-Type...

3-POINT PLOW A. Stands B. Proportional Valve C. Pitch Cylinder D. Depth Chain E. Water Level F. Tile Boot Rollers G. Removable Boot H. Shear I. Heel HYDRAULIC VALVES A. Down Pressure Manifold (Pull Type Plows Only) Controls Plow Wheels B. Proportional Control Valve Controls Plow Shank Pitch

SERIAL NUMBER TRACTOR SELECTION Horsepower is not the only thing to consider when selecting a tractor for the plow. - a lower horsepower tractor, properly weighted, may be able to do the job to your satisfaction. Generally, a tractor weighted to 24,000 lbs. or more can pull the plow very well in good soil conditions. You must also consider: • weight of the tractor • tire wear • type of tire (radial or bias) • height of the ti

If you are using the plow in good, dry soil conditions, it may be best to pull the plow without duals on the tractor. This will allow all of the weight of the tractor to be transferred to a smaller surface area. However, in less than ideal conditions, where the surface of the ground is slick or sticky, duals may enhance traction. We do not recommend pulling the plow in very muddy conditions as this will probably make your tiling job very frustrating and may cause compaction problems. The chart below will help you decide what tractor to choose based on the depth you want to pull. The depths...

3-POINT ZD PLOW HOOKUP AND GEOMETRY 3-point plow hookup is a Category III or IV attachment. Attachment to a Category IV 3-Point hitch is possible with the use of CAT III to CAT IV bushings. All pins and hardware come with the plow. Adjusting the top link is very important. The ideal appearance of the 3-point arms should be as shown. Correct Attach the top link to the bottom or lowest mounting hole on your tractor and the highest hole you can reach on the plow. Keeping an upward angle on the top link is critical. Please use the top hole on the plow for attaching the top link if possible....

HYDRAULICS The plow will come standard with pioneer hydraulic fittings. You will only need one set of hydraulic outlets. Make sure you connect to the tractor’s primary hydraulic remote. This remote will need to have its hydraulic flow (speed) turned up all the way if possible. Hydraulic fluid direction is important. In the front of each of the valve bodies is the letters “P” and “T”. “P” is for Pressure and “T” is for Tank. Note: If the fluid is in the wrong direction, the valves will not work correctly. Tie up all hydraulic hoses and take care to remove any dirt from tractor remote...

BOOT REMOVAL 1. Properly support funnel (B). 2. Remove bolt (A) and remove the funnel (B). 3. Remove bolt (C) and the poly shields (D) on either side of the plow. 4. Each size of boot has a corresponding shear (A). Remove and replace with the proper size shear. Installation is the reverse of removal.

SHEAR WEAR Over time, the shear will wear on the cutting edge. Gauge wear by placing a straight edge on the bottom of the cutting edge (A) of the plow. The shear (B) should be 1/8-1/4 inch below the heel (A). If it is less, replace the shear. Failure to replace the shear could result in adverse effects to the grading of the plow and excessive wear to the heel/bottom of the plow. TILE FEEDER (OPTIONAL) The optional tile feeder is a great addition to any plow. It is not required but is a great reassurance of tile quality. The tile feeder simply pushes on the tile to ensure no stretch is...