Catalog excerpts
Sensors - Information Spagnol Sensors are divided in two categories based on the electrical signal used: S-BUS The communication between sensor and controller takes place digitally. A single sensor can therefore transmit several measurements (eg: EC / pH / water temperature) See below for the selection of the type of cable to be used with this type of sensors. The signal is transmitted to the controller in the traditional way. . Each Spagnol controller-equipped product has a certain base number of both S-BUS and contact inputs that can be increased with the addition of expansion boards....
Open the catalog to page 2CLIMATIC SENSORS: Code Signal type S-BUS Electronic temperature and humidity sensor in ventilated box. Temperature range: -20°C ÷ +50°C (-4°F ÷ 122°F) Humidity range: 10% ÷ 98% Ingress protection: IP53 (NEMA 3) Cable ingress: PG13.5 Dry bulb / wet bulb temperature and humidity sensor in ventilated box. Temperature range: -20°C ÷ +50°C (-4°F ÷ 122°F) Humidity range: 10% ÷ 98% Ingress protection: IP53 (NEMA 3) Cable ingress: PG13.5 Electronic temperature and humidity sensor in environmental protection. Supplied with interface box. Cable length: 4 m. Temperature range:...
Open the catalog to page 3WEATHER SENSORS: The following sensor can be mounted on the weather station structure code 303002015 (max.5 sensors) or on the single sensor support code 303002021 (max.1 sensor). Every sensor is supplied with an S-BUS interface board. The board must be installed in to the support structure (303002015 or 303002021). Code Signal type S-BUS Solar radiation sensor. Radiation intensity range: 0 ÷ 2000 w/m2 Spectrum range: 400-950 nm Supplied with: 4 m cable (4x 0.5 mm2). S-BUS interface board Mounting screws kit Wind speed sensor. Wind speed range: 0.2 ÷ 60 m/s Supplied with: 7 m cable...
Open the catalog to page 45 SENSORS WEATHER STATION SUPPORT: Code 303002015 Sensors support Support for up to 5 weather sensors. Supplied in mounting kit (instruction included). Plastic box for up to 6 sensors S-BUS interface boards. Cable entries: - 6 PG9 for sensor cables. - 6 PG11 for cables from controller. Sensors Interface boards Signal type S-BUS Weather station with the following sensors: Rain presence sensor. Wind speed sensor. Wind direction sensor. Solar radiation sensor. Temperature and humidity sensor. Weather station with the following sensors: Rain presence sensor. Wind speed sensor. ...
Open the catalog to page 5Weather station with the following sensors: Rain presence sensor. Wind speed sensor. Solar radiation sensor. Weather station with the following sensors: Rain presence sensor. Wind speed sensor. Wind direction sensor. Solar radiation sensor. General catalogue
Open the catalog to page 6SENSORS SINGLE METEO SENSOR SUPPORT SYSTEM: Support for 1 meteo sensor composed by: Stainless steel sensor fixing bracket, suitable for mounting on Ø 32mm pole (pole code 303002019) Support for 1 meteo sensor composed by: Stainless steel sensor fixing bracket, suitable for mounting on Ø 32mm pole (pole code 303002019) Plastic box for the containment of the sensor S-BUS interface board. Stainless steel Support pole for weather sensor bracket (bracket code 303002020 and 303002021) Sensor support Sensor’s interface board
Open the catalog to page 7SENSORS PROCESS SENSORS: Code Signal type S-BUS Heating pipes temperature sensor. Measuring range: 0°C ÷ +130°C (32°F ÷ 266°F) Sensor thread: G½” male Sensor length: 60mm. Ingress protection: IP53 (NEMA 3) Hot buffer segment temperature sensor. Measuring range: 0°C ÷ +130°C (32°F ÷ 266°F) Sensor thread: G½” male Sensor length: 300mm. Ingress protection: IP53 (NEMA 3) Pressure sensor. Measuring range: -1bar ÷ +15 bar. 4 m cable (4x0.22) (junction box not supplied) Sensor thread: G¼” male Ingress protection: IP50 (NEMA 2) EC and pH sensor completed of: EC+temperature...
Open the catalog to page 8PROCESS SENSORS: Code Signal type S-BUS Tank water level sensor. Measuring range: 0 ÷ 10m water height, 1 cm resolution. Plastic box 80x120x55 with S-BUS interface box. The box is mounted on a stainless steel plate with holes for wall mounting. Submersible sensor with 15m of cable already connected to the interface box. Ingress protection: IP53 (NEMA 3) Cable entry from controller: PG13.5 ON/OFF water level sensor. Cable length: 10m IRRIGATION LINE FLOW SENSOR – FOR METALLIC PIPES: Flow sensor with collar for mounting on metal pipes Code External pipe diameter MIN (mm)...
Open the catalog to page 9SENSORS IRRIGATION LINE FLOW SENSOR – FOR PVC PIPES - T-FITTING SOLVENT CEMENT: Irrigation line flow sensor for PVC pipes, solvent cement version Code Pipe external diameter Signal type Connection cable: 3 wires, max.section 1 mm2, max.length 100m IRRIGATION LINE FLOW SENSOR – FOR PVC PIPES – SADDLE CLAMP: Irrigation line flow sensor for PVC pipes, saddle clamp version Code Pipe external diameter Signal type Connection cable: 3 wires, max.section 1 mm2, max.length 100m IRRIGATION LINE FLOW SENSOR – INFORMATION: Minimum distances of rectilinear pipe to be observed before and after the flow...
Open the catalog to page 10All SPAGNOL SRL catalogs and technical brochures
-
Gravimatic
2 Pages
-
UltraLP
4 Pages
-
ServoMix
5 Pages
-
Radio System
3 Pages
-
I-Fenix
4 Pages
-
G-Fenix
4 Pages
-
F-Fenix
4 Pages
-
EvoMix
10 Pages
-
EvoJet
8 Pages
-
DrenaMix
6 Pages
-
Drenamatic
1 Pages
-
DosaMix
6 Pages
-
DosaJet
6 Pages
-
C-Fenix
5 Pages
-
Ca-Remover Tank
2 Pages
-
Ca-Remover Line
2 Pages
-
BravoMix
10 Pages
-
BravoJet
8 Pages