Operator’s Manual CC2815, CC2835, CC2830 DC2815, DC2835, DC2830
154Pages

COULTER-CHISEL DISK-CHISEL COULTER-CHISEL DISK-CHISEL THE OPERATOR IS RESPONSIBLE FOR ADJUSTING THE MACHINE SINCE MACHINE DOES NOT COME “FIELD READY” FROM FACTORY. CAUTION READ & UNDERSTAND OPERATOR’S MANUAL BEFORE USING MACHINE. See www.summersmfg.com for the latest version of all Summers Operator’s Manuals. SUMMERS MANUFACTURING CO., INC. WEB SITE: www.summersmfg.com

Warranty Summers warrants only products of its manufacture against operational failure caused by defective materials or workmanship which occur during normal use within 36 months from the date of purchase by the end user from Summers’ dealer. Summers’ obligation is to replace free of charge any part of any product that Summers inspection shows to be defective excluding transportation charges to Devils Lake, ND and return and also excluding all transportation costs from Summers’ dealer to the dealer’s customer and all other costs such as removal and installation expense. Summers shall not be...

This manual provides the following information about your Summers Coulter-Chisel and Disk-Chisel. SECTION CONTENTS Section 1 – SAFETY explains important safety precautions and familiarizes the Operator with the decals and their locations. Section 2 – ASSEMBLY includes step by step assembly instructions. Section 3 – COULTER-CHISEL & DISK-CHISEL OPERATION provides necessary information for the operation and adjustment of the machine. Section 4 – MAINTENANCE covers recommended mechanical maintenance. Section 5 – TROUBLESHOOTING provides a quick reference to solving problems. SPECIFICATIONS...

SAFETY-ALERT SYMBOL This symbol is used to denote possible danger and care should be taken to prevent bodily injury. This symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Definition of each Signal Word used in conjunction with the Safety-Alert symbol. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is to limited to the most extreme situations. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which,...

SAFETY DURING TRANSPORT 1. ONLY TOW at a safe speed. Use caution when making corners or meeting traffic. 2. USE a safety chain between tractor drawbar and implement hitch when transporting on public roads. 3. ALWAYS use hydraulic cylinder transport locks when transporting on public roads. 4. FOLLOW ALL local laws governing transporting of farm machinery. 5. Frequently check for traffic from rear, especially during turns. SAFETY DECALS 1. KEEP SAFETY DECALS CLEAN. 2. REPLACE missing or unreadable decals. New decals are available from your Summers dealer by ordering correct part number (PN)...

SECTION 1 - SAFETY 3. PN 8Z0202 – DECAL FOR COMPANY IDENTIFICATION 4. PN 8Z0276 – DECAL FOR GENERAL CAUTION 5. PN 8Z0340 – DECAL FOR REPHASING CYLINDERS

SECTION 1 - SAFETY 6. PN 8Z0342 – DECAL FOR INSTALLING CYLINDER LOCKS 7. PN 8Z0344 – DECAL FOR STAYING CLEAR OF WINGS 8. PN 8Z0346 – DECAL FOR ELECTROCUTION DANGER 9. PN 8Z0348 – DECAL FOR GAUGE WHEEL DEPTH 10. PN 8Z0800 – AMBER REFLECTOR 11. PN 8Z0805 – RED-ORANGE REFLECTOR 12. PN 8Z0810 – RED REF

SAFETY LIGHT OPERATION The Summers Safety Light Kit is equipped with a 7 pin connector which meets SAE J560 specification. To protect 7 pin connector, store in dust cap (8K8067) when not attached to towing vehicle. On most towing vehicles WITHOUT brake lights: Amber lights will turn on with flashers or turn signals. Red lights will turn on with parking, road or field lights. On most towing vehicles WITH brake lights: Amber lights will turn on with flashers, turn signals OR when brake is applied. Red lights will turn on with parking or road lights. The Summers Safety Light Kit is equipped...

SECTION 2 – ASSEMBLY INTRODUCTION GENERAL ASSEMBLY SAFETY PRACTICES 1. READ AND UNDERSTAND Operator’s Manual before assembly of machine. 2. Machine should be assembled in a horizontal (field) position only. 3. If machine is to be assembled INDOORS, check that exit door is a MINIMUM OF 22’ WIDE. Height requirement varies up to 16’3”. Shanks may be left off to reduce height and width requirement. 4. Reference to “RIGHT” and “LEFT” is determined when machine IS VIEWED FROM THE REAR. 5. Reference to “FORWARD” means TOWARDS THE TRACTOR. 6. Reference to “REAR” means AWAY FROM THE TRACTOR....

SECTION 2 – ASSEMBLY INTRODUCTION GENERAL SAFETY PRACTICES YOU ARE RESPONSIBLE for the safe assembly of the machine. BLOCK UP ANY RAISED PART of the machine. Be sure machine is stable after blocking. DO NOT ALLOW CHILDREN or other unauthorized persons within the assembly area. ALWAYS INSPECT LIFTING CHAINS AND SLINGS for damage or wear. BE SURE LIFTING DEVICE IS RATED TO HANDLE THE WEIGHT. WEAR PERSONAL PROTECTIVE EQUIPMENT which includes a hard hat, eye protection, work gloves and steel toed boots with slip resistant soles. STOP ENGINE, place all controls in neutral, set parking brakes,...

SECTION 2 – SET-UP OF 16’ & 20’ DISK-CHISEL & COULTER-CHISEL MAIN FRAME 1. Place front, center and rear sections on floor with bolt plates facing each other. 2. ATTACH sections with 48 – 3/4x2-1/4” bolts, lock washers and nuts as shown. 3. Block center frames off the

SECTION 2 – SET-UP OF 16’ & 20’ DISK-CHISEL & COULTER-CHISEL MAIN FRAME 4. Install cylinder attach brackets with 3/4” u-bolts. NOTE: – Locate Rear Cylinder Attach Brackets (8T4224) 62” from frame center. 5. Insert eyebolts (8K1683) into each cylinder attach bracket. – Tighten 1-1/2” nuts so the same amount of threads are above top nut on all eyebolts. Insure that cylinder attach holes are aligned when eyebolts are tightened. 6. Liftarms will be centered beneath cylinder attach brackets. – Use 3/4” u-bolts for 4x4 to attach liftarm pivots (8T4100) to frame. – Slide pivot pin (8T3640) through...