Multipacka Front Press
20Pages

Multipacka Front Press Parts list 2017 and Operators Manual

Please complete this page and send it back to us at, Sumo UK Ltd. Redgates Melbourne York YO42 4RG Tel. 01759 319900 Fax. 01759 319901 SUMO SERIAL No: For your own records. (Serial plate on side of headstock) Multipacka Registration Document NAME: ADDRESS: Post Code SUMO SERIAL No.: (Serial plate on side of headstock) DEALERSHIP NAME AND BRANCH:

In order to obtain your free pair of Sumo overalls and baseball cap please fill in this form and send back to us at: Sumo UK Ltd Redgates Melbourne York YO42 4RG Tel. 01759 319900 Fax. 01759 319901 Overall size: tick where applicable Small (38 chest) Medium (42 chest) Large (46 chest) Extra large (50 chest) XX Large (54 chest) XXX Large (58 chest)

1.0 Summary The Sumo Multipacka Front press is a useful cultivation tool that allows land to be worked and evenly consolidated across the width of the machine allowing the following machine to work more effectlively. The main elements of this machine depend on the specification but will come with either rigid ripper tines mounted on a bolt on bracket on the front beam of the machine at 250mm spacings, Another specification is with levelling paddles that can be hydraulically adjusted to level ploughing ahead of consolidation. Before using the Sumo Multipacka Front Press it is absolutely...

3.0 Safety 3.1 Qualification and Training 3.2 General Safety 3.3 Special Safety Instructions 4.0 Operation and Adjustments 4.1 Operating 4.2 Adjustments 5.0 Maintenance 5.1 Spares 5.2 Winter Storage 6.0 Parts and Assembly 6.1 Overview 6.2 Ripper Tine Assembly 6.3 Scraper Assembly 6.4 Steering 6.5 Packer and Bearings 6.6 Folding Headstock 6.7 Folding Multipacka 6.8 Paddle Assembly 6.9 Paddle Hydraulics 6.8 Stickers and Paint

3.0 Safety This manual contains basic advice, which should be observed during setting-up, operation and maintenance. Therefore, this operating manual must be read by the personnel concerned prior to starting up and using the machine and be available at all times. If safety instructions are not complied with, then this can lead to the risk of injury to yourself and others as well as damage to the environment or the machine. Non-compliance to the safety instructions can also lead to claims for damages becoming invalid. 3.1 Qualification and Training  Reliable personnel may only perform any...

Warning signs and other notices on the machine provide important information for the safe operation. Observing them will serve your safety. Before starting work, make yourself familiar with all the equipment and controls as well as their functions. The user should wear close-fitting clothing. Check around the machine before moving off or starting up (watch out for children!). Make sure you have adequate all-round visibility. Always match your speed to the local conditions. Avoid sudden turning manoeuvres when driving uphill or downhill or when travelling across a slope. Observe the...

4.1 Operating The Sumo Multipacka Front Press should be set up so it runs level, this should be done by adjusting the top link appropriately, this will ensure the tools on the front are working effectively and no undue stresses are put onto the frames. If the machine is a hydraulic folding machine, the machine should be folded up for any transport and the “dog bone” transport lock placed across the two pins located on the outer hydraulic cylinder mounts. Both wings must be fully lowered before commencing work and when folding up the machine the transport lock should be replaced. The points...

5.0 Maintenance The condition of the tines and paddles should be monitored regularly to ensure excessive wear does not occur and wearing parts are replaced as required. The condition of the scrapers should be monitored regularly and adjusted or replaced as required to ensure they are working properly preventing soil building up on the packer. They must not be touching the packer though, as this will add to the rolling resistance and cause premature packer wear. The packer bearings should be greased with one pump of grease once a week and after washing off to remove water that may have been...

6.1 Rigid Multipacker Assembly PART NUMBER 3m Rigid Multipacka frame Trio Packer Bearing (60) 3m front press 609 Packer Ripper tine assembly Triple Scraper Hanger Full Assembly Trailed Trio & Subsoiler Multipacka Headstock Steering roller Steering roller washer 36mm Pin Cat II Lower Link Pin Front sumo/ Front Wright DO NOT SCALE DRAWING MACHINE/COMPONENT: Full Assembly Drawings and design information found herein remain the sole property of Sumo UK Ltd. Reproductions may only be made with the permission of the owner.

6.2 Ripper Tine Assembly PART NUMBER tine bracket Front Sumo Tine Assy Front Sumo Tine Pin M20 Ripper tine shear bolt DO NOT SCALE DRAWING MACHINE/COMPONENT: Ripper tine assembly Drawings and design information found herein remain the sole property of Sumo UK Ltd. Reproductions may only be made with the permission of the owner.

PART NUMBER Triple Scraper Hanger 609 Subsoiler/Trailed Trio Scraper M12 Cup head square DETAIL A SCALE 1 : 4 DO NOT SCALE DRAWING Scraper Assembly Drawings and design information found herein remain the sole property of Sumo UK Ltd. Reproductions may only be made with the permission of the owner.

ITEM PART NO. NUMBER 1 SW2054 Multipacka Headstock Steering roller Steering roller washer Steering components Drawings and design information found herein remain the sole property of Sumo UK Ltd. Reproductions may only be made with the permission of the owner.

PART NUMBER Trio Packer Bearing (60) 3m front press 609 Packer DO NOT SCALE DRAWING MACHINE/COMPONENT: Packer and Bearings Drawings and design information found herein remain the sole property of Sumo UK Ltd. Reproductions may only be made with the permission of the owner.

PART NUMBER Multipacka folding headstock Multipacka Linkage Headstock DO NOT SCALE DRAWING MACHINE/COMPONENT: Folding Headstock Drawings and design information found herein remain the sole property of Sumo UK Ltd. Reproductions may only be made with the permission of the owner.