TANCO AUTOWRAP 280 CS OPERATORS HANDBOOK WD66-280-M0207 Tanco Autowrap Ltd. Royal Oak Road, Bagenalstown, Co. Carlow, Ireland Tel.: +353 (0)5997 21336 Fax: +353 (0)5997 21560 E-Mail: [email protected] Internet: www.tanco.ie

Tanco Autowrap 280 CS Operator’s manual WARRANTEE Subject to hereunder provided, the sellers undertake to correct either by repair or at their election by replacement any defect of material or workmanship which occurs in any of its goods within twelve months after delivery of such goods to first user, with the exception of contractors or commercial users when warranty period is six months. In respect of Autowraps the warranty period is for 12 months or 8000 bales, whichever occurs first. In respect of Aerways, tine breakage will be assessed on an individual basis in every case. The term goods...

Tanco Autowrap 280 CS Operator’s manual General Safety Recommendations 7. Electrical Circuit Diagram 10. Film overlap system 12. Technical Diagrams 12.1. Film Threading Diagram 12.2. Gear Box chain drive tensioning system 12.3. Turntable Chain Drive tensioning system 12.4. Cut & Start Cylinder – recharging cylinder 13. Hydraulic Circuit Diagram 14. Closed Centre Conversion

Tanco Autowrap 280 CS Operator’s manual 1. GENERAL SAFETY RECOMMENDATIONS Before operating the machine, always ensure that the tractor and machine meet with work safety and road traffic regulations. In addition to recommendations given in this manual, legislation on work safety and accident prevention must also be respected. Advice is indicated on the machine, specifying safety recommendations in order to prevent accidents. Before travelling on public roads, the operator must ensure that the machine conforms to road traffic regulations. Before starting work, the operator must be familiar with...

Tanco Autowrap 280 CS Operator’s manual 18. Keep clear of the machine operating area. Warning! Danger of crushing and shearing can exist when components are operated by hydraulic or pneumatic controls. Before leaving the tractor or before adjusting, maintaining or repairing the machine, turn off the engine, remove the ignition key and wait until all moving parts have come to a complete stop. Do not stand between the tractor and the machine unless the hand break is tight and/or stops have been placed under the wheels. Before any adjustments, maintenance or repairs are carried out, ensure that...

Tanco Autowrap 280 CS Operator’s manual HYDRAULIC SYSTEMS 1. Warning! Hydraulic system is under pressure. 2. When fitting hydraulic motors or cylinders, ensure that connections have been made correctly, as per manufactures instructions. 3. CAUTION! Check whether Tractors hydraulics are open or closed centre. If you are unsure talk to you dealer. Running with the wrong circuit configuration will cause excessive heat in the hydraulic oil and may result in damage to the tractor and machine. To change configuration See Chapter 14. 4. Before connecting hoses to the tractor hydraulics, ensure that...

Tanco Autowrap 280 CS Operator’s manual 1.1. SPECIAL SAFETY INSTRUCTIONS 1. Stop engine of the tractor before working on machine. 2. Put a suitable prop under raised platform before working in this area. 3. Always raise lift Arm and fit safety prop before transporting machine on public roads. 4. Lift Arms should always be lowered before operating turntable. 5. Ensure platform rollers are parallel to Lift Arm before arm is raised. 6. On Autowrap models fitted with hydraulic bale ramp it is essential that the hydraulic hose is not disconnected from the hydraulic cylinder or hydraulic accumulator....

Tanco Autowrap 280 CS Operator’s manual 1.2. SAFETY DECALS The following safety decals have been placed on your machine in the areas indicated. They are intended for your personal safety and for the safety of the other people working with you. Walk around your machine and note the content and locations of these warning signs. Review these decals and the operating instructions in the manual with your machine operators. Ensure that these decals are always legible. If they are not, replace them. 1. READ OPERATORS MANUAL AND SAFETY INSTRUCTOONS 2. WARNING: SHARP BLADE 4. DO NOT EXCEED TURNTABLE SPEED...

Tanco Autowrap 280 CS Operator’s manual TECHNICAL SPECIFICATIONS Dimensions Total length – Excluding Bale Mat Width Height to top of side (bale guide) rollers Bale size Film (Width of Roll) 750 mm * The speed of rotation can be varied to suit various conditions but on no account should it exceed 30 r.p.m. (Speed in excess of 30 r.p.m. will void warranty).

Tanco Autowrap 280 CS Operator’s manual 3. PRE-DELIVERY INSTRUCTIONS IMPORTANT: DO NOT ATTEMPT TO OPERATE THE MACHINE UNTIL THE FOLLOWING INSTRUCTIONS ARE PERFORMED. OTHERWISE SERIOUS DAMAGE COULD BE CAUSED. 3.1. MACHINE ASSEMBLY For ease of transportation some items are removed from their positions and stored elsewhere on the machine. The bale ramp cylinder and Cut & Start unit are stored under the bale belt. On trailed models the cable guide is stored under the bale belt while on 3 point linkage models the top link bracket is stored under the belt. Also stored under the belt, on dispatch, is...

Tanco Autowrap 280 CS Operator’s manual Mounting Dispenser mast

Tanco Autowrap 280 CS Operator’s manual

Tanco Autowrap 280 CS Operator’s manual 3.7. Operational test When all above assembly and checks have been carried out, the operation of the machine should be checked as follows: NOTE: IF YOU ARE NOT TOTALLY FAMILIAR WITH THE OPERATION OF THE TANCO CONTROL SYSTEM, READ THIS MANUAL IN FULL BEFORE PROCEEDING WITH OPERATIONAL TEST. 1. Attach machine to tractor 2. Connect hydraulic hoses to D/A service on tractor. 3. Fit controller box inside cab. 4. Connect control box to the machine and connect power cable direct to the tractor battery. It is important that the leads are connected with the correct...

Tanco Autowrap 280 CS Operator’s manual 4. Transport Instruction 1. Never use straps around machine when lifting. Use only the following lifting points: - Tow hitch and two sockets on each side of Chassis at rear for trailed models. 3 pt. Linkage frame and two sockets on each side of Chassis at rear for 3 pt. Linkage Model. 2. Ensure the valve mount has been swung into the transport position. 3. When the machine is towed on the road the lifting arm (if fitted) must be in fully raised position, the safety prop fitted and the axle returned to narrowest position. 4. Raise the Parking Jack on trailed...