E100 SA QUICK REFERENCE GUIDE

Product catalog summary

Introduction
This document serves as a quick reference guide for the E100 SA bale wrapper, outlining essential procedures for operation, connection, and maintenance. It is important to refer to the Operators Manual for detailed instructions.

Initial Setup

Remove the transport pin from the load arm.
Remove the locking pin from the swivel axle, rotate the wheel to the working position, and reinsert the pin.
Adjust the dispenser to center the film on the bale.
Load the film roll into the dispenser, ensuring correct threading, and attach it to the Cut & Start.

Tractor Connection

Hydraulics: Connect the red pipe to the supply (25-30 lpm) and the blue pipe to the return (free flow return).
Electrics: Connect the 12V supply to the 3-pin plug and the wrapper harness to the controller.
Mount control levers within comfortable reach in the tractor cab.

Operation

Loading: Use lever No. 1 to lower the load arm, load the bale, and then lower the arm again.
Wrapping: Start table rotation with lever No. 2, increase speed after ½ revolution, and allow automatic wrapping. The table stops when the target wraps are reached.
Unloading: Use lever No. 3 to offload the bale and cut the film, then lower the table.

Entering Transport Position

Remove the locking pin, rotate the wheel to transport position, and reinsert the pin.
Rotate the table to the loading position, raise the load arm, and insert the transport pin.

Specifications

Model E100 SA: For 120 cm bales, use 16 wraps for 4 layers, 24 wraps for 6 layers, and 32 wraps for 8 layers. For 150 cm bales, use 20 wraps for 4 layers, 30 wraps for 6 layers, and 40 wraps for 8 layers.

Film Cutting Adjustment
The cutter closing point during tipping can be adjusted by moving the bolt on the linkage. Ensure the film is fully gathered on the cut and start frame when the cutter closes.

Catalog excerpts

E100 SA QUICK REFERENCE GUIDE The quick reference guide is not a substitute for the Operators Manual! Please refer to Operators Manual for more detailed information Red pipe > Supply (25-30lpm) Blue pipe > Return (Free flow return!!) 1. 2. Connect 12V supply to 3pin plug Connect wrapper harness to controller Control levers Mount the control levers in the tractor cab. Place it in a position that is in comfortable reach to the operator. ENTERING THE WORKING POSITION 1. Remove the transport pin from the load arm. 2. Remove the locking pin from the swivel axle and rotate the wheel into the working position. Reinsert the locking pin. 3. Adjust the position of the dispenser to ensure that the film will be applied to the centre of the bale. 4. Add the film roll into the dispenser, ensuring that it is threaded correctly, and attach the film to the Cut & Start.

Open the catalog to page 1

CONTROL LEVERS OPERATION Loading Unloading / Cut &Start Wrapping (Table rotation) CONTROLLER OPERATION Current No. of Wraps Channel Indicator RUN-ON Time + (Increase time to stop) RUN-ON Time – (Reduce time to stop) Program Key - Reset Store Total - Set Select Channel

Open the catalog to page 2

Lower the load arm to the ground using lever No. 1. Once the bale is inside the load arm, the bale can be loaded onto the table by operating lever No.1 in the opposite direction. Once the bale is loaded, the load arm can be lowered using lever No. 1. 4. To begin rotating the table, slowly move lever No. 2. 5. Once the table has completed approx. ½ revolution, the table speed can be increased by further moving lever No. 2. 6. Once 1 revolution is complete, lever No. 2 will be held in place by a magnet. This allows for Automatic wrapping. 7. When the target no. of wraps is reached lever No. 2 will...

Open the catalog to page 3

ENTERING THE TRANSPORT POSITION 1. Remove the locking pin from the swivel axle and rotate the wheel into the transport position. Reinsert the locking pin. 2. Rotate the table into the loading position. 3. Raise the load arm fully. 4. Insert the transport pin into the load arm. This will prevent the load arm from lowering when driving on the road. The transport pin should also be used when the machine is being parked. This is a guideline only! Misshapen bales may require more wraps to achieve full coverage . Model Bale Diameter 4 layres 6 layres 16 wraps 24 wraps 32 wraps 20 wraps 30 wraps 40...

Open the catalog to page 4

E100 SA QUICK REFERENCE GUIDE

E100 SA QUICK REFERENCE GUIDE

Catalog excerpts

All Tanco catalogs and technical brochures