Data Sheet R-Series V RM5 SSI Magnetostrictive Linear Position Sensors Super shield housing with IP68/IP69 against ingress of dust and water Position measurement with a resolution up to 0.1 μm Update rate up to 10 kHz

Temposonics® R-Series V RM5 SSI Data Sheet MEASURING TECHNOLOGY Position magnet (magnetic field) 2 The absolute, linear position sensors provided by Temposonics rely on the company’s proprietary magnetostrictive technology, which can determine position with a high level of precision and robustness. Each Temposonics® position sensor consists of a ferromagnetic waveguide, a position magnet, a strain pulse converter and a supporting electronics. The magnet, connected to the object in motion in the application, generates a magnetic field at its location on the waveguide. A short current pulse is...

Output Interface Data format Data length Data transmission rate Measured value Measurement parameters Resolution: Position Resolution: Velocity Update rate 2 Temperature coefficient Operating conditions Operating temperature Humidity Ingress protection Shock test Vibration test EMC test Operating pressure Magnet movement velocity Sensor electronics housing Sensor flange Sensor rod RoHS compliance Stroke length Temposonics® R-Series V RM5 SSI Data Sheet SSI (Synchronous Serial Interface) - differential signal in SSI standard (RS-485/RS-422) Binary or gray 70 kBaud L..1 MBaud, depending on cable...

Data Sheet Mounting instruction Please consult the technical drawings and the operation manual (document number: 552011) Connection type Cable outlet Power consumption 1.2 W typical Dielectric strength 500 VDC (DC ground to machine ground)

Temposonics® R-Series V RM5 SSI Data Sheet TECHNICAL DRAWING RM5-M/-S – RM5 with threaded flange M18×1.5 or ¾"-16 UNF-3A, example: Connection type HXX/PXX/RXX/TXX (cable outlet) Sensor electronics housing 170 (6.7) Threaded flange »M«: M18×1.5-6g Threaded flange »S«: ¾"-16 UNF-3A * Stroke length > 5000 mm (196.9 in.) Controlling design dimensions are in millimeters and measurements in ( ) are in inches Fig. 2: Temposonics® RM5 with ring magnet Super shield housing R-Series V sensor with connector outlet (connection type D84) Cable for direct connection to the controller (connection type HXX/PXX/RXX/TXX)...

Data Sheet Fig. 4: Connector wiring HXX/PXX/RXX/TXX

Temposonics® R-Series V RM5 SSI Data Sheet FREQUENTLY ORDERED ACCESSORIES – Additional options available in our Accessories Catalog Ring magnet OD33 Part no. 201 542-2 Ring magnet OD25.4 Part no. 400 533 Ring magnet Part no. 402 316 Material: PA ferrite GF20 Weight: Approx. 11 g Surface pressure: Max. 40 N/mm2 Fastening torque for M4 screws: 1 Nm Operating temperature: −40…+105 °C (−40…+221 °F) Material: PA ferrite GF20 Weight: Approx. 14 g Surface pressure: Max. 40 N/mm2 Fastening torque for M4 screws: 1 Nm Operating temperature: −40…+105 °C (−40…+221 °F) Material: PA ferrite Weight: Approx....

Temposonics® R-Series V RM5 SSI Data Sheet Cable connector* M12 A-coded female connector (8 pin), straight Part no. 370 694 Housing: GD-ZnAL Termination: Screw Contact insert: CuZn Cable Ø: 4…9 mm (0.16…0.35 in.) Wire: 0.75 mm2 Operating temperature: −25…+90 °C (−13…+194 °F) Ingress protection: IP67 (correctly fitted) Fastening torque: 0.6 Nm Material: PVC jacket; gray Features: Twisted pair, shielded, flexible Cable Ø: 6 mm (0.23 in.) Cross section: 3 × 2 × 0.14 mm2 Bending radius: 10 × D (fixed installation) Operating temperature: −40…+105 °C (−40…+221 °F) Material: PUR jacket; orange Features:...

Data Sheet Connection type M Threaded flange M18x1.5-6g (standard) S Threaded flange %"-16 UNF-3A (standard) Mechanical options Stroke length Standard stroke length (mm) Ordering steps (Note the temperature range of the cable!) See “Frequently ordered accessories” for cable specifications (Note the temperature range of the cable!) See “Frequently ordered accessories” for cable specifications |T|[Tm XX m/ft. PVC cable (part no. 530 032) See “Frequently ordered accessories” for cable specifications ITI[Tm XX m/ft. PTFE cable (part no. 530 112) See “Frequently ordered accessories” for cable specifications...

Data Sheet • Specify the number of magnets for your application and order the magnets separately. • The number of magnets is limited by the stroke length. The minimum allowed distance between magnets (i.e. front face of one to the front face of the next one) is 75 mm (3 in.). • Use magnets of the same type for differential measurement. • If the option for internal linearization in In “Options” is chosen, select a suitable magnet. Accessories have to be ordered separately. Mode 1 Measuring direction forward, asynchronous mode 2 Measuring direction forward, synchronous mode 1 3 Measuring direction...

Temposonics® R-Series V RM5 SSI Data Sheet Alarm The alarm bit is set by the sensor if the sensor detects more magnets (extra magnet) or less magnets (magnet status error) than configured. Asynchronous mode In asynchronous mode the position data is continuously updated inside the sensor as quickly as the sensor’s measurement cycle will allow, independent of the controller. The controller’s loop time will determine when the sensor’s most recent data is clocked out over the SSI interface. ( Synchronous mode) Parity The parity bit is a check bit that is added to a bit string to detect transmission...

UNITED STATES Americas & APAC Region Phone: +1 919 677-0100 E-mail: [email protected] Document Part Number: 552119 Revision A (EN) 06/2023 Temposonics 58513 Lüdenscheid GmbH & Co. KG Phone: +49 2351 9587-0 EMEA Region & India E-mail: [email protected] ITALY Phone: +39 030 988 3819 Branch Office E-mail: [email protected] FRANCE Phone: +33 6 14 060 728 Branch Office E-mail: [email protected] UK Phone: +44 79 21 83 05 86 Branch Office E-mail: [email protected] SCANDINAVIA Phone: + 46 70 29 91 281 Branch Office E-mail: [email protected] CHINA Phone: + 86 21 3405...