INSTRUCTION MANUAL timberwolf-uk.com

© Copyright Entec Industries Ltd 2015 The content of this publication may not be copied, reproduced, republished, posted, broadcast, transmitted or used in any way in any medium without the written permission of Entec Industries Ltd.

TIMBERWOLF TW 13/75G Section Page No. MACHINE DIMENSIONS & SPECIFICATIONS 2 PARTS LOCATION DIAGRAMS 3 Operator’s Personal Protective Equipment Required 5 Basic Woodchipping Safety 5 General Safety Matters - Do’s and Dont’s 6 Operator’s Personal Protective Equipment Required 8 Daily Checks Before Starting 9 Safe Lifting of Chipper 13 Copper Ease Safety Information 13 Engine Manufacturer’s Handbook 13 Tension Drive Belts 15 Greasing Rotor Bearings 15 EC DECLARATION OF CONFORMITY CERTIFICATE 17 V- BELT TENSIONING TABLE 21 WARRANTY SERVICE CHECK RECORD...

Thank you for choosing Timberwolf. Timberwolf chippers are designed to give safe and dependable service if operated according to the instructions. IMPORTANT HEALTH AND SAFETY INFORMATION Before using your new chipper, please take time to read this manual. Failure to do so could result in: - PERSONAL INjURY - EqUIPMENT DAMAGE - DAMAGE TO PROPERTY - 3RD PARTY INjURIES This manual covers the operation and maintenance of the Timberwolf TW 13/75G. All information in this manual is based on the latest product information available at the time of purchase. All the information you need to operate the...

Designed to chip solid wood material up to 75mm in diameter and capable of chipping over 0.75 tonnes of brushwood per hour. 1600 mm, (815 mm with funnel removed) The serial number can be found on the identification plate located on the side of the rotor housing. 1565mm (815mm with funnel removed) Engine type: Maximum power: Cooling method: Overall weight: Starting method: Type of feed: Honda 4 stroke OHV 9.6kW (13hp) Air cooled 188kg Recoil Gravity Maximum diameter material: 75 mm (3”) Fuel capacity: 6.5 litres Material processing capacity: 0.75 tonnes/hr Fuel type: Unleaded petrol

PARTS LOCATOR DISCHARGE HANDLE DISCHARGE BUCKET TOP ROTOR HOUSING BELT GUARD OPENING HANDLE ROTOR HOUSING CATCH BOLT SAFETY SWITCH PETROL TANK AIR FILTER COVER ENGINE

PARTS LOCATOR REAR BEARING HOUSING CUTTER BLADE ROTOR DRIVE PULLEY ENGINE PROTECTOR ENGINE PULLEY

SAFE WORKING The chipper will feed material through on its own. To do this, it relies on sharp blades both on the feed rollers and the chipper rotor. To keep the blades sharp, only feed the machine with clean brushwood. DO NOT put muddy/dirty wood, roots, potted plants, bricks, stones or metal into the chipper. OPERATOR'S PERSONAL PROTECTIVE EQUIPMENT REQUIRED Chainsaw safety helmet fitted with mesh visor and recommended ear defenders to the appropriate specifications. Close fitting heavy-duty non-snag clothing. Work gloves with elasticated wrist. Face mask if appropriate. Steel toe cap safety...

SAFE WORKING GENERAL SAFETY MATTERS ALWAYS stop the chipper engine before making any adjustments, refuelling or cleaning. DO NOT operate chipper unless available light is sufficient to see clearly. ALWAYS check rotor has stopped rotating and remove chipper ignition key before maintenance of any kind, or whenever the machine is to be left unattended. DO NOT use or attempt to start the chipper without the feed funnel, guards and discharge unit securely in place. ALWAYS operate the chipper with the engine set to maximum speed when chipping. ALWAYS check the machine is well supported and cannot move....

SAFE WORKING NOISE TEST MACHINE: TW 13/75G NOTES: Tested chipping 40mm x 40mm corsican pine 1.5m in length Noise levels above 80dB (A) will be experienced at the working position. Wear ear protection at all times to prevent possible damage to hearing. All persons within a 4 metre radius must also wear good quality ear protection. 90 .3d B Guaranteed Sound Power: 120dB (A) As required by Annex III of Directive 2000/14/EC “Noise Emission in the environment by equipment for use outdoors”

OPERATING INSTRUCTIONS SAFE TRANSPORTATION THE TW 13/75G chipper may be transported as a unit or with the feed funnel removed. TAKE care when loading the TW 13/75G as it is 183 kg in weight. STRAP the chipper down firmly before beginning a journey (do not use feed funnel handles to strap down machine). ENSURE no debris or water is trapped in the rotor housing that may spill during transit. TURN the fuel valve OFF and keep the engine upright. All Timberwolf TW 13/75G machines have a full pre - delivery inspection before leaving the factory and are ready to use. Read and understand this instruction...

OPERATING INSTRUCTIONS MOvE the throttle control lever to idle and allow to run for one minute. TURN the fuel valve to the ‘OFF’ position. EMERGENCY STOPPING Turn the ignition switch to the 'Off' position (as shown above). DAILY CHECKS BEFORE STARTING LOCATE the machine on firm level ground. CHECK engine oil level. CHECK the fuel valve is open. CHECK all guards are in place. CHECK the discharge unit is pointing in a safe direction. CHECK the feed funnel to ensure no objects are inside. For parts location see diagrams on pages 3 & 4. Do not use or attempt to start the chipper without the protective...

OPERATING INSTRUCTIONS BLADE WEAR The most important part of using a wood chipper is keeping the cutter blades sharp. Timberwolf chipper blades are hollow ground to an angle of 40 degrees. When performing daily blade checks ensure blade edge is sharp and free from chips, if there is any evidence of damage, or the edge is “dull” change the blade(s). The TW 13/75G is fitted with one blade 177 mm (7") long. It is 43 mm wide when new. A new blade should chip for up to 25 hours before it requires sharpening. This figure will be drastically reduced by feeding the machine with stony, sandy or muddy...

OPERATING INSTRUCTIONS THE FOLLOWING PAGES DETAIL ONLY BASIC MAINTENANCE GUIDELINES SPECIFIC TO YOUR CHIPPER. THIS IS NOT A WORKSHOP MANUAL. THE FOLLOWING GUIDELINES ARE NOT EXHAUSTIvE AND DO NOT EXTEND TO GENERALLY ACCEPTED STANDARDS OF ENGINEERING/MECHANICAL MAINTENANCE THAT SHOULD BE APPLIED TO ANY PIECE OF MECHANICAL EQUIPMENT AND THE CHASSIS TO WHICH IT IS MOUNTED. AUTHORISED TIMBERWOLF SERvICE AGENTS ARE FULLY TRAINED IN ALL ASPECTS OF TOTAL SERvICE AND MAINTENANCE OF TIMBERWOLF WOOD CHIPPERS. YOU ARE STRONGLY ADvISED TO TAKE YOUR CHIPPER TO AN AUTHORISED AGENT FOR ALL BUT THE MOST ROUTINE...