Product Segments • Industrial Motion TiMOTION's JP3 series inline linear actuator was designed for low load industrial applications where up to IP69K dust and liquid ingress protection is necessary. It is best suited for applications with visual or compact installation dimension requirements. Hall sensors are optional for the JP3 which allow for synchronization and position feedback. General Features Max. load Retracted length Output signals Black, grey Operational temperature range Operational temperature range at full performance Storage temperature range

Retracted length Load and Speed CODE Self Typical Current (A) Typical Speed (mm/s)Typical Current (A) Typical Speed (mm/s) Locking No Load With Load No Load With Load No Load With Load No Load With Load Force (N) 24V DC 24V DC 24V DC 24V DC 12V DC 12V DC 12V DC 12V DC Motor Speed (5600RPM, Duty Cycle 20% : 2min on / 8min off) B Note 1 Please refer to the approved drawing for the final authentic value. 2 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. The self-locking force is...

Motor Speed (5600RPM, Duty Cycle 20%: 2min on / 8min off) Speed vs. Load 25.0 Performance Data (24V DC Motor)

Motor Speed (5600RPM, Duty Cycle 20%: 2min on / 8min off) Speed vs. Load 25.0 Performance Data (12V DC Motor)

Rear Attachment (mm) See page 7 1 = Aluminum, U clevis, slot 4.2, depth 18.0, hole 10.2 Front Attachment (mm) See page 7 1 = Aluminum, slotless, hole 6.4 2 = Aluminum, slotless, hole 8.0 3 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 10.0 4 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 6.4 5 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 8.0 6 = Aluminum, hole 10.0 Direction of Rear Attachment (Counterclockwise) See page 8 Special Function of Spindle Subassembly Function of Limit Switches See page 8 1 = Two micro switches cut off the actuator at end of stroke 2 = Two micro switches cut...

JP3 Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B+C = Y 2. Retracted length needs to ≥ Stroke + Y A. Front Attachment

JP3 Ordering Key Appendix Rear Attachment (mm) 1 = Aluminum, U clevis, slot 4.2, depth 18.0, hole 10.2 11.7 Front Attachment (mm) 2 = Aluminum, slotless, hole 8.0 9 5 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 8.0 ø8 4 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 6.4 3 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 10.0 1 = Aluminum, slotless, hole 6.4

JP3 Ordering Key Appendix Direction of Rear Attachment (Counterclockwise) 1 = 0° Hole Functions for Limit Switches Wire Definitions CODE extend (VDC+) retract (VDC+) extend (VDC+) retract (VDC+) extend (VDC+) upper limit switch retract (VDC+) lower limit switch extend (VDC+) upper limit switch medium limit switch retract (VDC+) lower limit switch

JP3 Ordering Key Appendix Voltage 5 = 24V DC, PTC 100 250 PTC outside the motor; at cable length 100mm, min total cable = 250mm Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.