Product Segments • Industrial Motion TiMOTION's TA2 series linear actuator is compact, robust and capable of performing well in certain outdoor environments. This linear actuator is perfect for use in small spaces where force or capability cannot be sacrificed. Options include feedback sensors, signal sending limit switches and 90 degree clevis mounting. General Features Max. load Retracted length ≥ Stroke + 105mm (without output signals) Output signals Mechanical pot., embedded reed switch, NPN Hall sensor, Outer Adjustable Reed switch Operational temperature range Operational temperature range

Dimensions without Output Signals (mm) Dimensions with Output Signals

Load and Speed CODE Self Locking Force (N) Motor Speed (4200RPM, duty cycle 25%) A Motor Speed (6000RPM, duty cycle 25%) F Note 1 Please refer to the approved drawing for the final authentic value. 2 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. The self-locking force is a minimum value and can be actually higher. 3 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC. With a 36V DC...

Motor Speed (4200RPM, duty cycle 25%) Speed vs. Load 80.0 70.0 60.0

Motor Speed (6000RPM, duty cycle 25%) Speed vs. Load 80.0 70.0 60.0 F

Rear Attachment (mm) See page 8 1 = Aluminum, slotless, hole 6.4, one piece casting with 4 = Aluminum, U clevis, slot 6.0, depth 10.5, hole 6.4, gearbox one piece casting with gearbox 2 = Aluminum, slotless, hole 8.0, one piece casting with 5 = Aluminum, U clevis, slot 6.0, depth 10.5, hole 8.0, gearbox one piece casting with gearbox 3 = Aluminum, slotless, hole 10.0, one piece casting with 6 = Aluminum, U clevis, slot 6.0, depth 10.5, hole 10.0, gearbox one piece casting with gearbox Front Attachment (mm) See page 9 1 = Aluminum, slotless, hole 6.4 2 = Aluminum, slotless, hole 8.0 3 = Aluminum,...

TA2 Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B+C = Y 2. Retracted length needs to ≥ Stroke + Y A. Rear / Front Attachment Front Attachment

TA2 Ordering Key Appendix Voltage 5 = 24V DC, PTC 4 = Aluminum, U clevis, slot 6.0, depth 10.5, hole 6.4, one piece casting with gearbox 3 = Aluminum, slotless, hole 10.0, one piece casting with gearbox 2 = Aluminum, slotless, hole 8.0, one piece casting with gearbox 1 = Aluminum, slotless, hole 6.4, one piece casting with gearbox 5 = Aluminum, U clevis, slot 6.0, depth 10.5, hole 8.0, one piece casting with gearbox 6 = Aluminum, U clevis, slot 6.0, depth 10.5, hole 10.0, one piece casting with gearbox

TA2 Ordering Key Appendix Front Attachment (mm) 2 = Aluminum, slotless, hole 8.0 ø8.0 4 = Aluminum, U clevis, slot 6.0, depth 16.0, hole 6.4 5 = Aluminum, U clevis, slot 6.0, depth 16.0, hole 8.0 3 = Aluminum, U clevis, slot 6.0, depth 16.0, hole 10.0 6=A luminum, slotless, hole 10.0 1 = Aluminum, slotless, hole 6.4 Direction of Rear Attachment (Counterclockwise) 1 = 90°

TA2 Ordering Key Appendix Connector 1 = DIN 6P, 90° plug Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.