M6-13M SAWMILL MANUAL SWING-BLADE PRODUCT GUIDE $14,000 USD The M6-13M Sawmill is 6” x 6” standard cut, 5” x 12” double cut, fitted with Honda GX390 Petrol 11hp (net), 13hp (gross) engine. 1-800-598-6344 (USA Dealer ) 1-833-961-1904 (Parts / Technical Support / Warr

Key features: Manual Swing-Blade Portable Sawmill Our manual mills are incredibly simple and versatile. The frame is built tough and offers rigid cutting. Our single beam design provides unrestricted access to load logs and recover your lumber (you are not stuck between two tracks). Sizing is performed at the same end through two reduction gearboxes with large dials for sizing. The gearbox means that you will not rely on preset clicks for every movement, they are infinitely variable. Although the sizing is all done at one end, you still get the option to adjust for taper at the far end through...

Disassembly (6 assemblies including jockey wheels): 1. Unbolt the long alloy tube. Unbolt the operator end frame. a. You may use the included jockey wheels to prop up the beam during disassembly. You may also remove the long base skids of each frame to reduce the weight. Roll the carriage off the beam onto a pellet in your truck. 4. To reduce the overall weight of your carriage you may also remove: a. Guards. b. Blade. b. Motor (only four bolts on the 13hp). 5. Unbolt the far end frame. 6. Place the complete beam on your truck’s roof rack or disassemble into pieces for easier transport. View...

Mobility (Farm Dolly kit): You may also purchase the farm dolly kit as an accessory which means you can simply lower the complete sawmill onto this kit, then install the tow hitch bracket at the end of the beam and within minutes transport your sawmill around your property using your vehicle. • Electric start. • Log setup taper alignment included. • 1 x 5-tooth INSERT blade, tool, extra tips, and sharpener (requires a drill). • 1.2-meter diameter (4 feet) log - although any diameter may be sawn. • Manual feed. • Manual blade swing. • Single end horizontal and vertical gearbox with sizing dials....

Fits all Turbosawmill models. Runs on single phase power (small generator for remote use). Very accurate system. Includes new function allowing quick and easy sectional deep horizontal/vertical cuts. A great time saver! Available in both Metric and Imperial. *Email for freight quote. Dedicated Slabber Head Powered by the Honda GXV390 (13hp gross) engine. Cuts up to 1.5m wide slabs and can fit any Turbosawmill product. Shares the beam with the Swing-blade. *Email for freight quote. Manual Center Leg & 6ft Extension 6 feet long beam, leg, tongue inserts, tube, clamps and chain extensions. *Email...

6 feet long beam, tongue inserts, tube, clamps and chain extensions. *Email for freight quote. Planer Blade Planer blade for re-surfacing slabs and beams. Process is done after your product has dried. Provides a finished result. * $50 USD Freight charge. Planer blade replacement tip. * $50 USD Freight charge. Min 12 units. Secures your log during sawing. Alloy materials to reduce damage to your blade if hit by accident. * $50 USD Freight charge. 5 feet long handle. Used to roll logs. * $50 USD Freight charge.

Turbosawmill insert blade, 5 tooth, 9/32” kerf. 1 x blade. $50 USD Freight charge. 9/32” KERF, suits all models, includes lock screw. 1 x tip. * $50 USD Freight charge. Min 10 units. 1/4” KERF, suits all models, includes lock screw. 1 x tip. * $50 USD Freight charge. Min 10 units. Standard Shank 13/64” wide, fits all models. * $50 USD Freight charge. Min 10 units. Narrow Shank 5/32” wide, fits all models. Offers more clearance and life to your bit. * $50 USD Freight charge. Min 10 units.

Milling Made Easy www.turbosawmillusa.com 1-800-598-6344 (USA Dealer) 1-833-961-1904 (Parts / Technical Support / Warranty)