Weighing equipment
24Pages

Manual and safety instructions Appendix WI-5000-T: Operators Manual “Digi-star EZ 400” Appendix WI-5000-TS: Operators Manual “Risseeuw spreading computer” WIFO-Anema B.V. Hegebeintumerdyk 37 – 9172 GP Ferwert – Holland Telefoon  (0031) 518411318 – Telefax  (0031) 518411563 www.wifo.nl – email:

This manual gives information about the commencement of operation, use and maintenance of your newly purchased WIFO weighing equipment. Also included in this manual are a number of safety instructions to create a safe working environment. WIFO-Anema B.V. continuously aims to improve its products. WIFO-Anema B.V. reserves the right to introduce any changes and improvements deemed necessary without prior notice. Please read the manual thoroughly and observe the safety procedures before putting the unit into operation. Contact your dealer for any further questions or concerns you may have. We...

1.2 Safety precautions and warnings Please read this manual before you put the machine into operation for the first time, and observe the safety instructions at all times. The most important instructions are marked with a symbol. Any person in charge of the commencement of operation, the operation itself or the maintenance of the machine is urged to carefully read and observe the following instructions. Do not stand below the weighing equipment and stay out of the working area of the built-on equipment. Be mindful of falling goods.

Transport the load in the lowest possible position to increase the stability of the vehicle.

Safety stickers and warning signs A safe working environment also requires personnel to be well-informed about the various safety stickers on the machine. Be aware of the hazards they warn you to look out for. Replace any loose, illegible or missing stickers. Several safety stickers have been put onto the machine. The meaning of the stickers on this machine is as follows: N.B.: Please read the instructions from the manual prior to any maintenance to the machine. Turn off the engine and remove the key from the ignition for the time maintenance on the machine is carried out! Danger: Always...

WIFO weighing equipment can be used for weighing goods up to 5,000 kg. Forces up to 1,000 kg may be brought in the horizontal plane of the weighing equipment. WIFO weighing equipment is only to be used in combination with a tractor with a standard category II/III 3-point power lift. ATTENTION: The lifting capacity of the tractor / telescopic handler / front-end loader must exceed the overall mass of the weighing equipment and the load. The lifting capacity of the weighing equipment may not exceed 5,000 kg. ATTENTION: The weighing equipment may not be used in combination with e.g. excavators...

Any person working with or on the machine must have read this manual. The machine is to be used for its intended purpose only. Included in the intended purpose are, among other things: 1. Work must be carried out in accordance with the directions and within the functional restrictions (e.g. maximum hydraulic working pressure) as outlined in the regulations. Use only sound and appropriate tools. 2. Electric / electronic equipment and accessories (e.g. cables) must be treated in accordance with the general accepted policy for using non-waterproof portable electric and electronic equipment,...

Table 2.1.1-Models of WIFO weighing equipment 1 In category II 3-point power lift / In category III 3-point power lift. Extension details: The tractor must have a standard category II/III 3-point power lift. Optional extras: - Extension triangle. /1 'V Zero adjustment-setting and calibration have been realised by the manufacturer.

The following description refers to the add-on unit for a tractor with a 3-point power lift: Make sure the drawbars of the power lift of the tractor are at the same level. Couple the 3-point weighing equipment to the category II/III 3-point power lift of the tractor. Use the spacer sleeves to fill up the drawbars. Use good-quality locking clips. Adjust the upper control arm to ensure the weighing equipment is in an absolute vertical position. Only very little lateral play of the weighing equipment in the power lift is allowed. Make the adjustments via the stabilizers of the power lift....

Commencement of operation WI-5000-TS The following description refers to the add-on unit for a tractor with a 3-point power lift: Check that the drawbars of the power lift of the tractor are at the same level. Couple the 3-point weighing equipment to the category II/III 3-point power lift of the tractor. Use the spacer sleeves to fill up the drawbars. Use good-quality locking clips. Adjust the upper control arm to ensure the weighing equipment is in an absolute vertical position. Only very little lateral play of the weighing equipment in the power lift is allowed. Make the adjustments via...

Accessories/optional extras2.4.1 Extension triangle for WI-5000-T/WI-5000-TS Purpose of use: A piece of equipment, such as a fertilizer spreader, must be fitted with an extension triangle to be attached to the weighing machine. Commencement of operation: Jr | 't Welding an extension triangle to a piece of equipment must be carried out by a professional * welder/mechanic. Operating instructions: Make sure the carrier frame is in line with the extension triangle so that the pin fits through the hole in the extension triangle and can be secured using the lock pin and the spring clip. Table...

Faults and maintenance N.B.: Please read the instructions from the manual prior to any maintenance to the machine! Turn off the engine and remove the key from the ignition for the time maintenance on the machine is carried out! Make sure the weighing equipment is in the lowest position during maintenance. Prevent any inadvertent operation of the weighing equipment during maintenance by turning the tractor engine off and taking the key from the ignition. Warning: Do not conduct any welding jobs on the weighing equipment to prevent damage to the weighing sensors. Remove the weighing equipment...