FP1413
19Pages

FP1413 Woodland Firewood Processor OWNER’S MANUALWARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.

PREMIUM BAND SAW BLADES Part # HM126B

Introduction Congratulations on your purchase and welcome to Woodland Mills. This manual gives you the necessary information about your machine so you will be able to use it properly. The entire manual must be read and understood before you start using the machine. If any questions should arise that are not covered by this manual, please contact our customer service at 1-855-476-6455. Company presentation Woodland Mills was co-founded in 2009 by Neil Bramley & Josh Malcolm after the pair recognized the need for a portable sawmill that balanced quality and value. Since successfully launching...

A very efficient and user friendly log splitter that cuts and splits the log in one operation. Produces about 1 cord an hour. Splits logs up to 24" long and 13" in diameter. Equipped with automatic splitter which means that the splitter starts automatically after the log is cut. The saw chain is activated by a button on the saw chain handle and stops automatically when not in use. This ensures high safety, lower noise and longer life of both chain and bar. Max splitting force Max log diameter Max cutting length Log production Gas Motor Saw chain (length - gauge - pitch) Weight Splitting...

Safety The machine may only be used in the manner prescribed in this manual. Deviations may lead to that the health and safety requirements are not met. The user is responsible to read through the instructions and follow them properly. Never tamper with the machine’s functionality or construction. It may lead to a deterioration of safety! Never leave the machine unattended during operation! Symbol explanation Wear safety goggles Wear protective clothing Wear safety shoes Wear safety helmet Wear hearing protectors Wear safety gloves

Operation safety The machine may only be used by one person at a time. No other than the user may stay in the risk area around the machine. The risk area covers 9' around the machine. Personal safety Protective equipment must be used while operating the machine. Machine safety The machine is intended for use in outdoor environment and for log splitting only. To obtain best functionality, do not split the logs into pieces shorter than 12”. Check before each use that the auto splitter stops when the protective cage is opened! If this feature does not work, the machine must not be used! Never...

Assembly 1. Remove processor and all parts from the steel shipping crate. 2. Insert axle through the processor ensuring it is centered and tighten the bolts to hold it securely in place. Note, it is important to ensure the two holes are facing up as they are used to hold the wheel fenders in place. 3. Place a liberal amount of grease on the inside of the wheel hubs and in the bearings. Insert greased bearing, washer and nut over axle spindle and tighten the nut. The cotter pin can be ...

4. Install the fenders and attach to the axle using the two bolts as shown below. 5. The four lug nuts of each wheel should be torque to 90 ft-­‐lbs. 6. Match hydraulic line “A” up with fitting “A” on the control valve and tighten with a wrench. 7. Match hydraulic line “B” up with fitting “B” on t

8. Install the hydraulic line to the chainsaw bar as per the images below and tighten with wrench. 9. Latch the spring into the slot. This spring is used to aid in returning the chainsaw bar handle. 10. Install the chainsaw bar guard and tighten the 3 bolts in the areas shown bel

11. Remove the adhesive backing from the chainsaw bar guard and position the bar oil tank in place. Tighten nut to securely hold it in place. Attach the oil line to the spout on the chainsaw bar as shown in below right image. 12. Install the chainsaw bar pull handle using the three bolts shown below. Also ensure the cable shown in the image on the right is in the lower hole. 13. Install “L” shaped plate as shown below so that when the chainsaw bar handle is pulled down, the plate will...

14. Install the cage guard in place and tighten the three bolts as shown below. 15. Install the notched plate on the processor with the three nuts and bolts provided. This plate is used to lock the handle in place which holds the 2/4 way splitter at the desired height.

16. Install the 2/4 way splitter bottom support as shown below. The handle can also be installed at this point along with the 2/4 way splitter itself. 2/4 Way Handle Splitter 17. Install log deck roller assembly as shown in below images.

18. The chain can now be adjusted to ensure the tension is set correctly. Proper chain tension is achieved when the chain can be pulled away from the bar by hand ¼”-­‐ ½”. To tighten or loosen the chain, the two bolts can be loosened using a ½” wrench. Next, the allen key bolt can be turned clockwise to tighten or counter-­‐clockwise to loosen the chain. The two ½” bolts can be tightened again to hold the bar securely. With the firewood processor now assembled, the conveyor system can be...

21. The top half of the conveyor can now be installed to the bottom half by bolting it at the seam using the hardware shown below. Be sure to install one of the washers in between the top and bottom conveyor. The nut should be left loose so that the bolts act as a hinge and allow the conveyor system to fold in half. Also, be sure that the conveyor is looped around the top roller. Washer